Briggs & Stratton 195764GS, 20228 Operate pressure washer only outdoors, When Adding Fuel

Page 3

Section 1: Safety Rules

WARNING

Running engine gives off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea, fainting or death.

Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning.

Operate pressure washer ONLY outdoors.

Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.

DO NOT operate pressure washer inside any building or enclosure.

Use a respirator or mask whenever there is a chance that vapors may be inhaled.

Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.

WARNING

Use of pressure washer can create puddles and slippery surfaces.

High pressure spray could cause you to fall if you are too close to the cleaning surface.

Keep spray nozzle between 8 to 24 inches away from cleaning surface.

Operate this unit on a stable surface.

The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces.

Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

If engine starts and fails to continue to run or if increased resistance is felt during starting pull attempts, squeeze trigger on spray gun.

WARNING

Fuel and its vapors are extremely flammable an explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

Turn pressure washer OFF and let it cool at least 2 minutes before removing gas cap.

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel expansion.

Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

DO NOT tip engine or equipment at angle which causes fuel to spill.

DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

Transport/repair with fuel tank EMPTY or with fuel shutoff valve OFF.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

Store away from furnaces, stoves, water heaters, clothes dryers or other appliances that have pilot light or other ignition source because they can ignite fuel vapors.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and

possible amputation.

Spray gun retains high pressure when pressure washer is shut down, which can cause injury.

NEVER aim spray gun at people, animals or plants.

DO NOT allow CHILDREN to operate pressure washer.

NEVER repair high pressure hose. Replace it.

Keep high pressure hose connected to pump and spray gun while system is pressurized.

Squeeze trigger on spray gun to relieve trapped pressure, every time you stop engine. Engage trigger lock on spray gun.

WARNING

Spray contact with electrical wiring can result in electrocution.

Keep water spray away from electric wiring or fatal electric shock may result.

3

Image 3
Contents Manual del Propietario Table of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelHigh pressure spray may damage fragile items including glass Pump equipped with Automatic Cool Down System Features and Controls SectionKnow Your Pressure Washer Nozzle Extension with Quick Connect Allows youPreparing Pressure Washer for USE AssemblyCarton Contents Attach Handle and Accessory TrayAdd Engine Oil and Fuel AssemblyConnect Hose and Water Supply to Pump Checklist Before Starting EnginePressure Washer Location HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Operation SectionHow to Stop Your Pressure Washer How to Use Accessory TrayOperation Follow these instructions to change ProjectPro nozzles How to Use ProjectPro Nozzle SystemHow to Use the Turbo Nozzle Cleaning and Applying DetergentTo apply detergent follow these steps Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemPressure Washer Maintenance Section MaintenanceSpecifications General Maintenance RecommendationsUse wire here MaintenanceNozzle Maintenance Ring MaintenanceChange pump oil as follows Engine MaintenancePump Maintenance Changing Pump OilProtecting the Pump StoragePreparing the Unit for Storage Storing the EngineTroubleshooting TroubleshootingProblem Cause Correction Year Consumer Use Years Years orReglas DE Seguridad Reglas de SeguridadConserve Estas Instrucciones Tabla DE Contenidos Descripción DEL EquipoCuando Añada Combustible Sección 1 Reglas de SeguridadPrecaución Conozca SU Maquina Lavadora DE Presion Características y ControlesMontaje MontajePreparando EL Lavador a Alta Presión Para SU USO Sección 3 Montaje Agregar Aceite al Motor y GasolinaColoque la lavadora a presión sobre una superficie nivelada Lista de Revision Previa al Arranque del Motor Conecte la Manguera y el Suministro de Agua a la BombaCómo Darle Arranque a su Máquina Lavadora a Presión OperaciónCómo Usar SU Máquina Lavadora a Presión Ubicación del Lavadora a PresiónSección 4 Operación Cómo Detener su Máquina Lavadora a PresiónUtilización de la Bandeja de Accesorios Coloque el pestillo de seguridad de la pistola de rociado Cómo Usar el Sistema de Boquillas ProjectProLa Presión Baja La Presión AltaPara aplicar el detergente, siga los siguientes pasos Cómo Usar la Boquilla a ChorroLimpieza y Aplicación del Detergentes Detergentes caseros podrían dañar la bombaPara Enjuage Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento DE LA Maquina Lavadora a Presion MantenimientoEspecificaciones Recomendaciones GeneralesMantenimiento de la Bomba Sección 5 MantenimientoMantenimiento de la Boquilla Mantenimiento de los Anillos OAlmacenando EL Motor Sección 5 y 6 Mantenimiento y AlmacenamientoMantenimiento DEL Motor Preparando LA Unidad Para SU AlmacenamientoReparacion DE Averias Diagnosticos de AveríasGarantía Limitada

195764GS, 20228 specifications

Briggs & Stratton is a name synonymous with reliable power and performance in small engine solutions. The Briggs & Stratton 20228,195764GS is a prime example of their commitment to innovation, durability, and efficiency. This engine is primarily designed for a variety of applications, including outdoor power equipment and generators, making it an ideal choice for both commercial and residential use.

One of the standout features of the 20228,195764GS is its robust design. Built with high-quality materials, this engine is engineered to withstand the rigors of heavy use. The construction is not only durable but also lightweight, allowing for easy maneuverability and installation. This feature proves advantageous for lawnmowers, pressure washers, and generators, ensuring they operate efficiently under various working conditions.

In terms of power, the 20228,195764GS engine delivers impressive performance, providing reliable output to tackle tough jobs with ease. With an optimized combustion system, it ensures maximum fuel efficiency while minimizing emissions. This is pivotal in meeting environmental standards while also lowering operational costs for users.

Furthermore, the engine integrates advanced technologies that enhance overall functionality. The patented ReadyStart technology simplifies the starting process, eliminating the need for manual choke adjustments. This ensures a hassle-free startup every time, making it user-friendly, especially for those new to operating similar equipment.

Another notable characteristic is the engine’s maintenance-friendly design. When servicing is required, access to components is straightforward, reducing downtime and improving user experience. Briggs & Stratton also emphasizes long-lasting performance, with features like strong air filtration systems to extend engine life by protecting it from contaminants.

The 20228,195764GS is also designed for versatility. It can power various attachments and machines, making it suitable for different tasks, from landscaping to construction purposes. Briggs & Stratton's reputation for quality and innovation is evident in this model, which reflects their commitment to meeting the diverse needs of their customers.

Overall, the Briggs & Stratton 20228,195764GS combines power, efficiency, and ease of use, making it an exceptional choice for consumers looking for a reliable engine solution. This model not only embodies the brand's legacy but also sets a standard for what modern small engines should deliver, ensuring that projects can be completed seamlessly and efficiently.