Briggs & Stratton 195764GS, 20228 Check In-Line Filter, Nozzle Maintenance, Ring Maintenance

Page 15

Section 5: Maintenance

Check In-Line Filter

Refer to Figure 18 and service the in-line filter if it becomes clogged, as follows:

Figure 18 — Clean In-Line Filter

Filter Screen

Nozzle Extension

O-ring

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush screen, spray gun, and nozzle extension with clean water to clear debris.

2.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push screen in with eraser end of pencil until it rests flat at bottom of opening.Take care not to bend the screen.

3.Place o-ring into recess. Push o-ring snugly against in- line filter screen.

4.Assemble nozzle extension to spray gun, as described earlier in manual.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the nozzle following these instructions:

1.Shut off engine and turn off water supply.

2.Remove nozzle from end of nozzle extension.

3.Remove in-line filter from other end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting nozzle (Figure 19).

Figure 19 — Nozzle Maintenance

Use wire here

to remove

debris.

5.Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 20). Back flush between 30 to 60 seconds.

Figure 20 — Backflushing the Nozzle Extension

6.Reinstall nozzle and in-line filter into nozzle extension.

7.Reconnect nozzle extension to spray gun.

8.Reconnect water supply, turn on water, and start engine.

9.Test pressure washer by operating with each quick connect nozzle.

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number 191922GS by contacting the nearest authorized service center. It is not included with the pressure washer.This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Manual del Propietario Table of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelHigh pressure spray may damage fragile items including glass Pump equipped with Automatic Cool Down System Features and Controls SectionKnow Your Pressure Washer Nozzle Extension with Quick Connect Allows youPreparing Pressure Washer for USE AssemblyCarton Contents Attach Handle and Accessory TrayAdd Engine Oil and Fuel AssemblyConnect Hose and Water Supply to Pump Checklist Before Starting EnginePressure Washer Location HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Operation SectionHow to Stop Your Pressure Washer How to Use Accessory TrayOperation Follow these instructions to change ProjectPro nozzles How to Use ProjectPro Nozzle SystemHow to Use the Turbo Nozzle Cleaning and Applying DetergentTo apply detergent follow these steps Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemPressure Washer Maintenance Section MaintenanceSpecifications General Maintenance RecommendationsUse wire here MaintenanceNozzle Maintenance Ring MaintenanceChange pump oil as follows Engine MaintenancePump Maintenance Changing Pump OilProtecting the Pump StoragePreparing the Unit for Storage Storing the EngineTroubleshooting TroubleshootingProblem Cause Correction Year Consumer Use Years Years orReglas DE Seguridad Reglas de SeguridadConserve Estas Instrucciones Tabla DE Contenidos Descripción DEL EquipoCuando Añada Combustible Sección 1 Reglas de SeguridadPrecaución Conozca SU Maquina Lavadora DE Presion Características y ControlesMontaje MontajePreparando EL Lavador a Alta Presión Para SU USO Sección 3 Montaje Agregar Aceite al Motor y GasolinaColoque la lavadora a presión sobre una superficie nivelada Lista de Revision Previa al Arranque del Motor Conecte la Manguera y el Suministro de Agua a la BombaCómo Darle Arranque a su Máquina Lavadora a Presión OperaciónCómo Usar SU Máquina Lavadora a Presión Ubicación del Lavadora a PresiónSección 4 Operación Cómo Detener su Máquina Lavadora a PresiónUtilización de la Bandeja de Accesorios Coloque el pestillo de seguridad de la pistola de rociado Cómo Usar el Sistema de Boquillas ProjectProLa Presión Baja La Presión AltaPara aplicar el detergente, siga los siguientes pasos Cómo Usar la Boquilla a ChorroLimpieza y Aplicación del Detergentes Detergentes caseros podrían dañar la bombaPara Enjuage Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento DE LA Maquina Lavadora a Presion MantenimientoEspecificaciones Recomendaciones GeneralesMantenimiento de la Bomba Sección 5 MantenimientoMantenimiento de la Boquilla Mantenimiento de los Anillos OAlmacenando EL Motor Sección 5 y 6 Mantenimiento y AlmacenamientoMantenimiento DEL Motor Preparando LA Unidad Para SU AlmacenamientoReparacion DE Averias Diagnosticos de AveríasGarantía Limitada

195764GS, 20228 specifications

Briggs & Stratton is a name synonymous with reliable power and performance in small engine solutions. The Briggs & Stratton 20228,195764GS is a prime example of their commitment to innovation, durability, and efficiency. This engine is primarily designed for a variety of applications, including outdoor power equipment and generators, making it an ideal choice for both commercial and residential use.

One of the standout features of the 20228,195764GS is its robust design. Built with high-quality materials, this engine is engineered to withstand the rigors of heavy use. The construction is not only durable but also lightweight, allowing for easy maneuverability and installation. This feature proves advantageous for lawnmowers, pressure washers, and generators, ensuring they operate efficiently under various working conditions.

In terms of power, the 20228,195764GS engine delivers impressive performance, providing reliable output to tackle tough jobs with ease. With an optimized combustion system, it ensures maximum fuel efficiency while minimizing emissions. This is pivotal in meeting environmental standards while also lowering operational costs for users.

Furthermore, the engine integrates advanced technologies that enhance overall functionality. The patented ReadyStart technology simplifies the starting process, eliminating the need for manual choke adjustments. This ensures a hassle-free startup every time, making it user-friendly, especially for those new to operating similar equipment.

Another notable characteristic is the engine’s maintenance-friendly design. When servicing is required, access to components is straightforward, reducing downtime and improving user experience. Briggs & Stratton also emphasizes long-lasting performance, with features like strong air filtration systems to extend engine life by protecting it from contaminants.

The 20228,195764GS is also designed for versatility. It can power various attachments and machines, making it suitable for different tasks, from landscaping to construction purposes. Briggs & Stratton's reputation for quality and innovation is evident in this model, which reflects their commitment to meeting the diverse needs of their customers.

Overall, the Briggs & Stratton 20228,195764GS combines power, efficiency, and ease of use, making it an exceptional choice for consumers looking for a reliable engine solution. This model not only embodies the brand's legacy but also sets a standard for what modern small engines should deliver, ensuring that projects can be completed seamlessly and efficiently.
Top Page Image Contents