Briggs & Stratton 195764GS, 20228 Pressure Washer Rinsing, Cleaning Detergent Siphoning Tube

Page 13

Section 4: Operation

3.Place small filter end of detergent siphoning tube into detergent container.

CAUTION

Keep the chemical injection tube from coming in contact with the hot muffler.

•When inserting the filter into a detergent solution bottle, route the tube so as to keep it from inadvertently contacting the hot muffler.

4.Make sure black cleaning detergent nozzle is installed.

NOTE: Detergent cannot be applied with the high pressure nozzles (Yellow, Orange or Red).

5.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump and start engine.

6.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

7.Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

IMPORTANT:You must flush the chemical injection system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.

Pressure Washer Rinsing

For Rinsing:

1.Apply trigger lock to spray gun.

2.Remove black cleaning detergent nozzle from nozzle extension.

3.Select and install desired high pressure nozzle following instructions “How to Use ProjectPro™ Nozzle System”.

4.Keep spray gun a safe distance from the area you plan to spray.

WARNING

High pressure spray could cause you to fall if you are too close to the cleaning surface.

•Keep spray nozzle between 8 to 24 inches away from cleaning surface.

•Operate this unit on a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

5.Apply a high pressure spray to a small area and then check the surface for damage. If no damage is found, you can assume it is okay to continue rinsing.

6.Start at top of area to be rinsed, working down with same overlapping strokes as you used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

1.Place chemical injection siphon/filter in a bucket full of clean water.

2.Attach black cleaning detergent nozzle.

3.Flush for 1-2 minutes.

4.Shut off engine.

IMPORTANT: Simply shutting OFF engine will not release pressure in the system. When the engine has shut down, squeeze the trigger on the spray gun to relieve the pressure in the hose.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Manual del Propietario Safety Rules Table of ContentsEquipment Description Operate pressure washer only outdoors When Adding FuelHigh pressure spray may damage fragile items including glass Know Your Pressure Washer Features and Controls SectionNozzle Extension with Quick Connect Allows you Pump equipped with Automatic Cool Down SystemCarton Contents AssemblyAttach Handle and Accessory Tray Preparing Pressure Washer for USEAdd Engine Oil and Fuel AssemblyConnect Hose and Water Supply to Pump Checklist Before Starting EngineHow to Start Your Pressure Washer HOW to USE Your Pressure WasherOperation Section Pressure Washer LocationHow to Use Accessory Tray How to Stop Your Pressure WasherOperation Follow these instructions to change ProjectPro nozzles How to Use ProjectPro Nozzle SystemCleaning and Applying Detergent How to Use the Turbo NozzleTo apply detergent follow these steps Pressure Washer Rinsing Cleaning Detergent Siphoning TubeAutomatic Cool Down System Thermal ReliefSpecifications Section MaintenanceGeneral Maintenance Recommendations Pressure Washer MaintenanceNozzle Maintenance MaintenanceRing Maintenance Use wire herePump Maintenance Engine MaintenanceChanging Pump Oil Change pump oil as followsPreparing the Unit for Storage StorageStoring the Engine Protecting the PumpTroubleshooting TroubleshootingProblem Cause Correction Year Consumer Use Years Years orConserve Estas Instrucciones Tabla DE Contenidos Reglas de SeguridadDescripción DEL Equipo Reglas DE SeguridadCuando Añada Combustible Sección 1 Reglas de SeguridadPrecaución Conozca SU Maquina Lavadora DE Presion Características y ControlesMontaje MontajePreparando EL Lavador a Alta Presión Para SU USO Agregar Aceite al Motor y Gasolina Sección 3 MontajeColoque la lavadora a presión sobre una superficie nivelada Lista de Revision Previa al Arranque del Motor Conecte la Manguera y el Suministro de Agua a la BombaCómo Usar SU Máquina Lavadora a Presión OperaciónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónCómo Detener su Máquina Lavadora a Presión Sección 4 OperaciónUtilización de la Bandeja de Accesorios La Presión Baja Cómo Usar el Sistema de Boquillas ProjectProLa Presión Alta Coloque el pestillo de seguridad de la pistola de rociadoLimpieza y Aplicación del Detergentes Cómo Usar la Boquilla a ChorroDetergentes caseros podrían dañar la bomba Para aplicar el detergente, siga los siguientes pasosLimpiando el Tubo Enjuage de la Máquina Lavadora a PresiónSistema de Enfriamiento Automático Alivio Térmico Para EnjuageEspecificaciones MantenimientoRecomendaciones Generales Mantenimiento DE LA Maquina Lavadora a PresionMantenimiento de la Boquilla Sección 5 MantenimientoMantenimiento de los Anillos O Mantenimiento de la BombaMantenimiento DEL Motor Sección 5 y 6 Mantenimiento y AlmacenamientoPreparando LA Unidad Para SU Almacenamiento Almacenando EL MotorReparacion DE Averias Diagnosticos de AveríasGarantía Limitada

195764GS, 20228 specifications

Briggs & Stratton is a name synonymous with reliable power and performance in small engine solutions. The Briggs & Stratton 20228,195764GS is a prime example of their commitment to innovation, durability, and efficiency. This engine is primarily designed for a variety of applications, including outdoor power equipment and generators, making it an ideal choice for both commercial and residential use.

One of the standout features of the 20228,195764GS is its robust design. Built with high-quality materials, this engine is engineered to withstand the rigors of heavy use. The construction is not only durable but also lightweight, allowing for easy maneuverability and installation. This feature proves advantageous for lawnmowers, pressure washers, and generators, ensuring they operate efficiently under various working conditions.

In terms of power, the 20228,195764GS engine delivers impressive performance, providing reliable output to tackle tough jobs with ease. With an optimized combustion system, it ensures maximum fuel efficiency while minimizing emissions. This is pivotal in meeting environmental standards while also lowering operational costs for users.

Furthermore, the engine integrates advanced technologies that enhance overall functionality. The patented ReadyStart technology simplifies the starting process, eliminating the need for manual choke adjustments. This ensures a hassle-free startup every time, making it user-friendly, especially for those new to operating similar equipment.

Another notable characteristic is the engine’s maintenance-friendly design. When servicing is required, access to components is straightforward, reducing downtime and improving user experience. Briggs & Stratton also emphasizes long-lasting performance, with features like strong air filtration systems to extend engine life by protecting it from contaminants.

The 20228,195764GS is also designed for versatility. It can power various attachments and machines, making it suitable for different tasks, from landscaping to construction purposes. Briggs & Stratton's reputation for quality and innovation is evident in this model, which reflects their commitment to meeting the diverse needs of their customers.

Overall, the Briggs & Stratton 20228,195764GS combines power, efficiency, and ease of use, making it an exceptional choice for consumers looking for a reliable engine solution. This model not only embodies the brand's legacy but also sets a standard for what modern small engines should deliver, ensuring that projects can be completed seamlessly and efficiently.
Top Page Image Contents