AquaPRO PRO1300 TCE, PRO1300h/c TCE, PRO1100e TCE owner manual Electronic Temp. Controls

Page 5

PRO1300, PRO1100e, PRO1300h/c, PRO1100, PRO1300h/c TCE, PRO1300 TCE, PRO1100e TCE

Basic Heat Pump

Operation (continued)

Overheating, short-circuiting and fire damage will result from inadequate wiring.

All units are equipped with an electrical wiring schematic inside the electrical panel. If this is missing, please contact the factory at 1-877- 278-2797 to obtain one.

All units are to be wired for 230 VAC, 1 phase. These units require a dedicated 50-amp breaker or time delay fuse.

Pool Heater is to be installed in accordance with Article 680 of the National Electrical Code (NEC), NFPA 70, and within the requirements of all local codes having jurisdiction.

Electronic Temp. Controls

All Units Except PRO1100

Description

•The control located on the front of your heat pump has a large three- character display for the water temperature, set points, and diagnostics (see figure 3 for front panel appearance). The three button keypad includes SET, UP arrow, and DOWN arrow buttons. LED indicators next to the display show if the heat pump is in the pool mode or in the spa mode and if the unit is running.

Figure 3 - Front Panel

Buttons

Press the SET button to change between modes and use the up and down arrows to change the selected mode’s settings.

Modes available are:

POL - allows you to change the pool water temperature set point

SPA - allows you to change the spa water temperature set point

P-S- changes between pool and spa settings. LED’s on front panel will indicate current mode selected.

F-C- display temperature in Fahrenheit or Celsius

TCE UNITS ONLY:

FIL - used to set system run time.

H/C UNITS ONLY:

H-C- change between heating and cooling mode.

Water Temperature Set Point

Temperature set point range is OFF, and 61°F to 95°F for POL mode. For SPA mode, set point range is OFF, and 61°F to 104°F. Pushing the UP arrow or DOWN arrow buttons will prompt the control to display the current set point. Continuing to press the UP or DOWN buttons will allow the set point values to scroll until the desired set point is reached. Once the new set point has been reached, stop pressing the UP or DOWN buttons. Once the unit toggles back to the current water temperature display, the set point is entered. The controls have a feature called “Set Point Memory Retention”. If the power is removed from the unit, it retains the last set point displayed.

Connecting to a Remote System: All Units Except Pro1100

This Pool Heater is compatible with all known remote systems in the industry. The following models’ diagrams show how to connect all of the remote systems to the Electronic Temp. Controller.

For 2 wire remotes

1.Bring up “POL” setting and arrow temperature down until pool setting reads “off”.

2.Bring up “SPA” setting and arrow temperature up until spa setting reads 104.

3.Set unit to the “POL” mode.

4.Connect remote system with 2 wires to the P/S terminal on control board (see specific model wiring diagram).

For 3 wire remotes

1.Bring up “POL” setting and use arrows to select desired pool temperature.

2.Bring up “SPA” setting and use the arrows to select the desired spa temperature.

3.Set unit to the “POL” mode.

4.Connect the common and high (or spa) wires to the “P/S” terminals on control board (see specific model diagram). Low or pool wire does not get connected.

Note: For heat/ cool units, the remote will not work in the cooling mode.

Connecting to Remote Systems: PRO1100

This Pool Heater is compatible with 2- wire remote systems only, and is not compatible with 3 wire remote systems. Figure 4 shows where to connect the remote systems to the Temperature Controller.

Connection to AquaLink, Compool, Hayward, AquaLogic or any other 2 wire remote system with their own thermostat:

•Remove gray jumper from terminals 1 and 2 on TB1.

•Bring the two wires from the remote system to terminals 1 & 2 on Terminal Block 1 (TB1).

•The Temperature Control knob must be turned clockwise (highest temp. setting) for the remote system to operate the Pool Heater properly.

High Temperature Lock Out: All Units Except PRO1100

Your heat pump includes a special feature to “lock” the high temperature settings. This eliminates the need for a thermostat lock-box. This prevents unauthorized persons from adjusting the heat pump above these desired limits. To activate this feature, please call AquaPRO® Systems at 877-AQUA-SYS (877-278-2797) during business hours 8 AM to 5 PM EDT Monday through Friday and we will be glad to assist in setting up this feature.

Phone: (877)-278-2797

www.aquaprosystems.com

3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Heat Pump Pool Heater Bomba DE Calor Para Piscinas Page Installation Procedures ContentsImportant Safety Instructions Operation Basic Heat PumpUnit Location PlumbingElectronic Temp. Controls PRO1100 Manual Temperature ControlsIndicator Lights PRO1300 PRO1100ePRO1300h/c PRO1300, PRO1100e, PRO1300h/c, PRO1100PRO1300 TCE PRO1100e TCEActivating and Setting System Run Time TCO Operation PRO1100e TCE & PRO1300 TCE wiring diagramPRO1300h/c TCE Toggling Between Heating and Cooling ModeElectronic Temp Controls Selecting Functionality of UnitActivating and Setting system run time MaintenanceUnit leaves the factory with the FIL mode set to OFF Time Clock Override TCO OperationApplication Guidelines Troubleshooting GuideTroubleshooting Limited Warranty Guías de seguridad ÍndiceInspección de la unidad Procedimientos de instalaciónUbicación de la unidad PlomeríaControles electrónicos de temperatura Todas las Procedimientos deFuncionamiento básico de la bomba de calor Luces indicadoras Controles electrónicos de temperaturaControles de temp. manuales Figura 5 diagrama de cableado Selección de la funcionalidad de la unidad PRO1100e TCE PRO1300 TCEOperación con Eliminación del Temporizador TCE Ciclo de descongelaciónPara TCO opcional Operación con Limitación del Temporizador TCOLa unidad viene de fábrica con el modo FIL apagado OFF Figura 9 Diagrama de cableadoVea la Figura 9 para el cableado de la función TCE Condensación Pautas de aplicaciónCubiertas para piscinas MantenimientoAberturas de la piscina Guía de diagnóstico y resolución de problemasCondiciones climáticas DiagnósticosGuía de diagnóstico y resolución de 13 Sp Garantía LimitadaNotas

PRO1100e, PRO1300 TCE, PRO1300, PRO1100, PRO1100e TCE specifications

The AquaPRO PRO1300h/c TCE, PRO1300 TCE, PRO1100e TCE, PRO1100, and PRO1100e are a series of high-performance water treatment systems designed to meet the diverse needs of residential and commercial users. These models stand out due to their advanced technology, energy efficiency, and user-friendly operation, making them ideal for various water purification tasks.

The AquaPRO PRO1300h/c TCE is equipped with advanced filtration technology that combines multiple filtration stages, ensuring the removal of contaminants, odors, and unpleasant tastes from the water. Its high-capacity system is perfect for larger households or small businesses, treating up to 1,300 gallons per day. This model features a compact design, which simplifies installation and saves valuable space, while providing a robust solution for clean drinking water.

The PRO1300 TCE model mirrors many features of the PRO1300h/c but is tailored for specific applications where heating or cooling functions are not necessary. It retains the high filtration capacity and incorporates smart technology that allows users to monitor water quality in real-time. The user-friendly interface and app connectivity offer convenient access to system status and maintenance alerts.

Moving down the range, the AquaPRO PRO1100e TCE offers slightly lower filtration capabilities but maintains the same commitment to quality and efficiency. Perfect for medium-sized households, the PRO1100e TCE boasts an eco-friendly design that minimizes energy consumption without compromising on performance. It features a smart leak detection system that alerts users in the event of any leaks, safeguarding both the unit and the property.

The PRO1100 is a more basic model intended for users seeking simplicity without sacrificing performance. It offers reliable filtration with easy-to-replace cartridges and minimal maintenance requirements, making it an excellent choice for those new to water filtration systems.

Lastly, the PRO1100e is designed for environments where energy efficiency is prioritized. Its reduced operational costs make it particularly attractive to eco-conscious consumers. With durable construction and a simple interface, these models ensure longevity and ease of use, appealing to a wide demographic.

In conclusion, the AquaPRO range encompasses various models, each with distinct features that cater to different filtration needs while ensuring high-quality performance, making the AquaPRO systems a wise investment for clean, safe water.
Top Page Image Contents