Maintenance | Zenoah SRTZ2601F specification

SRTZ2601F

9. Maintenance

ENGINE

SHAFT

MAINTENANCE CHART

			Every	Every	Every
System/components	Procedure	Before	25	50	100	Note
System/components	Procedure	use	hours	hours	hours	Note
		use	hours	hours	hours
			after	after	after
fuel leaks, fuel spillage	wipe out	✔
fuel tank, air filter, fuel filter	inspect/clean	✔	✔			replace, if necessary
idle adjusting screw	see adjusting	✔				replace carburetor
idle adjusting screw	idling speed	✔				if necessary
	idling speed					if necessary
spark plug	clean and readjust			✔		GAP: .025 in (0.6 ~ 0.7 mm)
spark plug	plug gap			✔		replace, if necessary
	plug gap					replace, if necessary
cylinder fins, intake air cooling vent	clean		✔
muffler, spark arrester, cylinder exhaust port	clean, remove piled up carbon				✔
throttle lever, ignition switch	check operation	✔
cutting parts	replace if	✔
cutting parts	something’s wrong	✔
	something’s wrong
gear case, cutter case	grease		✔
screws/nuts/bolts	tighten/replace	✔			✔	not adjusting screws

•Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool.

•Use protective gloves whenever inspecting, removing, sharpening, and installing the blades.

BLADES

•When refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades.

•If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they fit more closely together.

1.Loosen lock nut (A) as shown in the diagram.

2.Tighten screw (B) fully, and then turn one-third to one- half of a rotation backward.

3.While holding onto the screw to keep it in position, tighten the lock nut.

4.Check to make sure that the flat washer (C) is loose enough so that it may be turned by pressing on it with a finger.

(1)Upper blade

(2)Lower blade

NOTE

•Screwing in the screw too tightly may make it impos- sible for the blades to move. Conversely, not screw- ing in the screw tightly enough may make the blades of the trimmer feel dull and cause leaves and branches to become caught in the blades of the trimmer.

QUICK TIP

•If the blades become so worn down that it is no longer possible to eliminate the gap between them, you should contact the authorized ZENOAH servicing dealer from which you purchased your ZENOAH trim- mer to have the blades resharpened or replaced.

GEAR CASE

•The reduction gears are lubricated by multipurpose, lithium-based grease in the gear case. Supply new grease every 25 hours of use or more often depend- ing on the job condition. When adding lubricant, use a grease gun to insert lubricant into the three grease nipples located on the gear case.

TYPE OF LUBRICANT TO BE USED

Always be sure to use #2 lithium heat-resistant lubricant.

(1) Grease fitting

GB-12

SRTZ2601F specifications

The Zenoah SRTZ2601F is a high-performance, professional-grade brushcutter designed for demanding landscaping tasks. Known for its robust construction and innovative technologies, this model is a favorite among landscape professionals and enthusiasts alike.

One of the standout features of the SRTZ2601F is its powerful 25.4cc two-stroke engine. This engine is engineered for both performance and fuel efficiency, delivering impressive torque and speed while minimizing emissions. The power-to-weight ratio of the SRTZ2601F is optimized, providing excellent maneuverability, which is essential for tasks in tight spaces or thick vegetation.

The unit is equipped with advanced starting technology, including a digital ignition system that ensures easy starts with minimal effort, even in cold weather. The anti-vibration system incorporated into the design significantly reduces operator fatigue, allowing for prolonged use without discomfort. This system absorbs the vibrations generated by the engine, providing a smoother experience during operation.

The cutting attachment of the Zenoah SRTZ2601F features a dual cutting line head that allows for efficient trimming and edging. The head is designed for quick line replacement, reducing downtime during work. Additionally, users have the option to switch out the cutting head for blades, making the tool versatile for different types of vegetation.

The ergonomic design of the brushcutter promotes comfortable handling. The adjustable handle is easily configurable to suit the user's height and preferences, enhancing control and precision while in use. The lightweight design, coupled with a well-balanced construction, ensures that even extended periods of work become less tiring.

In terms of durability, the SRTZ2601F is built with high-quality materials that can withstand the rigors of daily use. Its rugged casing protects the internal components from impacts and environmental conditions, ensuring longevity and reliability.

Furthermore, this model supports various accessories, allowing for customization based on individual needs. Whether dealing with tough brush, trim work, or heavy-duty clearing tasks, the Zenoah SRTZ2601F is designed to meet the challenges head-on, making it an indispensable tool for anyone serious about landscaping.

Overall, the Zenoah SRTZ2601F combines power, efficiency, and user-friendly features, making it a top choice for both professional landscapers and home gardening enthusiasts looking for a reliable brushcutter.