Zenoah SRTZ2401 manual OP5, OP6 Stopping Engine OP3, Adjusting Throttle Cable

Page 30

English

8. Operation

OP5

.04 in

(1~2mm) (1)

OP6

(1)

■STOPPING ENGINE (OP3)

1.Release the throttle lever and run the engine for a half minute.

2.Shift the ignition switch to the STOP position.

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

■ADJUSTING THROTTLE CABLE

•The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP5)

(1) cable adjuster

■ADJUSTING IDLING SPEED (OP6)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter- clockwise.

(1) idle adjusting screw

NOTE

•Warm up the engine before adjusting the idling speed.

WARNING

•This product is equipped with extremely sharp blades, and when used improperly these blades can be extremely dangerous, and improper handling can cause accidents which may in turn lead to serious injury or death. For this reason, you should always be careful to follow the following instructions when using your trimmer.

•Never hold the trimmer in a way in which the blades are pointed towards someone else.

•Never allow the blades to come into proximity with your body while the engine of the trimmer is in operation.

•Always be sure to turn off the engine before

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SRTZ2401 Information Informationinformación Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Symbols on the machine PositionEmission Control Control DE Emisiones EmplacementPosición Information Importante Concernant LE MoteurFor safe operation Working ConditionWorking Circumstance Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineAvant DE Mettre LE Moteur EN Marche Plan DE TravailPlan DE Trabajo Antes DE Arrancar EL MotorUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL ProductoMaintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoHandling Fuel Refill after cooling the engineTransportation Llenar una vez que el motor se haya enfriado Manipulation DU CarburantManipulación DEL Combustible TransportAttaching the Trimming Mechanism SE2 Set upSE1 SE2 Installing Handle Balance UnitInstalación DEL Mango Assemblage MontajeMise EN Place DE LA Poignee Equilibrage DE LA MachineWhen using Zenoah genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile Zenoah Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Operation OP1 OP2 OP3 OP4 Starting EngineCutting head will start rotating upon the engine starts Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Ajuste DE LA Velocidad DE Marcha EN Vacío OP6OP7 Adjusting the Angle of the Cutting Blades OP7 Clamp bolt Trimming mechanism Tighten LoosenAjuste DEL Ángulo DE LAS Cuchillas DE CORTE. OP7 Réglage DE Langle DES Lames Tranchantes OP7Boulon de serrage Mécanisme de coupe Serrer Desserrer Perno de sujeción Mecanismo de poda Ajustar AflojarMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoQuick TIP MA1Blades MA1 MA2Entretien Mantenimiento AIR Filter Replacement Plug is a NGK CMR7HMA3 MA4 MA5 Fuel FilterFiltre a Carburant Filtro DE Combustible Filtre a AIRFiltro DE Aire Bougie D’ALLUMAGE BujíaSpark arrester Muffler MA6Spark Arrester Intake AIR Cooling VentParachispas PARE-ETINCELLESOuïe DU Refroidissement PAR AIR Toma DE Aire DE RefrigeraciónMA7 MA8 Procedures to be Performed After Every 100 Hours of USEStorage Cylinder Intake air cooling vent backCylindre Ouïe d’entrée d’air de refroidissement arrière Procedure a Effectuer Toutes LES 100 Heures D’UTILISATIONRangement Almacenamiento Cilindro Toma de aire de refrigeración posteriorTroubleshooting guide 11. Guía de localización y solución de problemasGuide de localisation des pannes SRTZ2401 NotaParts list Cutting Unit SRTZ2401 S/N Z000001 and up Engine Unit SRTZ2401 S/N 60100101 and up Qty Key# Part Number Description Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC

SRTZ2401 specifications

The Zenoah SRTZ2401 is a remarkable example of modern technology in the realm of small engine equipment. Renowned for its high performance and efficiency, this versatile power tool has gained popularity among professionals and enthusiasts alike. One of the standout features of the SRTZ2401 is its lightweight design, making it easy to maneuver for extended periods without causing undue fatigue, which is a significant advantage for users who rely on mobility during their tasks.

At the heart of the SRTZ2401 is a robust 24cc two-stroke engine, designed for optimal power output while maintaining fuel efficiency. This engine configuration not only provides ample torque for demanding applications but also ensures quicker throttle response, allowing users to achieve precise control in various settings. The advanced combustion technology integrated into this model ensures cleaner emissions, highlighting Zenoah's commitment to environmental sustainability.

The SRTZ2401 is equipped with an easy-start system that minimizes the effort required to start the engine, thus enhancing the user experience, especially for those who might struggle with recoil starters. Additionally, the engine features a durable construction that promotes longevity and reliability. The combination of high-quality materials and innovative design means that users can depend on this tool for a variety of applications, from gardening to landscaping.

Another noteworthy characteristic of the SRTZ2401 is its anti-vibration technology, which significantly reduces user fatigue and enhances comfort during operation. This feature is particularly beneficial for professionals who spend long hours in the field, ensuring a smoother and more enjoyable experience. The ergonomic handle design further contributes to this comfort, providing a secure grip that allows for precision handling.

In terms of versatility, the Zenoah SRTZ2401 offers compatibility with various attachments, expanding its usability beyond a single function. This adaptability makes it a valuable asset for anyone in need of a multi-purpose tool. Whether users require a trimmer, edger, or blower, the SRTZ2401 can meet those needs with ease.

In summary, the Zenoah SRTZ2401 stands out for its lightweight and effective design, powerful engine, user-friendly features, and adaptability for multiple applications. This combination of characteristics makes it a top choice for those seeking quality and efficiency in their outdoor power tools. With its advanced technologies, it embodies both performance and innovation, making it a staple in the small engine market.
Top Page Image Contents