Zenoah CHT2200 manual SE6 SE7 SE8

Page 20

SE6

SE7

SE8

English

6. Set up

■CHT2200

1.Attach the engine to the clutch housing of the cutter unit. Casually fix the front 2 points with the screws (.55" long).

2.After connecting the ground wire, install the rear handle to the clutch housing with the screw(2" long) and the nut.

3.Put the screw (1.6" long) through the ground wire terminal and the rear handle, and in to the engine mounting base. Securely tighten all of the engine mounting screws.

4.Attach the front handle onto the gear housing and fasten with 2 screws (1.2" long) and nuts.

5.Connect the throttle cable with the lever on the rear handle, and secure the end with the hardware attached to the handle.

6.Check the cable play and, if necessary, adjust between .04” and .08” by bending throttle wire receiver of the bracket with needle nose pliers.

20

Image 20

Contents HT2200 CHT2200 Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Model HT2200 CHT2200 SpecificationsParts location Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Modelo HT2200 CHT2200Symbols on the machine Emission ControlEmplacement PosiciónControl DE Emisiones Fabricado PORWorking Circumstance For safe operationWorking Condition Consignes de securite Instrucciones de seguridad Conditions DE TravailCondición DE Trabajo Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaCut only materials recommended by Using the ProductStarting the Engine Demarrage DU Moteur Utilisation DE LA MachineArranque DE LA Máquina Empleo DEL ProductoMaintenance If Someone ComesConsignes de securite Instrucciones de seguridad SI QUELQU’UN S’APPROCHEEntretien SI SE Acerca AlguienTransportation Handling FuelRefill after cooling the engine Manipulation DU Carburant TransportManejo DEL Combustible Llenar una vez que el motor se haya enfriadoSet up Blade Washer Keep LooseBolt Plate Nut Corrugate tube 2 Tie band Throttle cable 4Throttle leverAssemblage Montaje SE6 SE7 SE8 Assemblage Montaje Recommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile Zenoah Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitAbastecimiento DE LA Unidad Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteClose OperationStarting Engine Fonctionnement Uso Adjusting Idling Speed HOW to USEStopping Engine Idle set screwReglage DU Regime DE Ralenti Ajuste DE LA Velocidad EN VacíoVis de reglage du ralenti Tornillo de fijación libre Comment UtiliserHorizontal cut Hedge Trimming TechniquesVertical cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is Champion RCJ6Y or NGK BPMR7A AIR FilterFuel Filter Spark PlugEntretien Mantenimiento Blades Spark Arrester MA4Intake AIR Cooling Vent PARE-ETINCELLES MA4 Parachispas MA4Ventilación DE Refrigeración DEL Aire Ouïe DE Refroidissement PAR AIR DE AdmisiónProcedures to be Performed After Every 100 Hours of USE StorageSharpening MA7 Reduction GearboxRangement Almacenamiento Guide de localisation des pannes Troubleshooting guide10. Guía de localización y solución de problemas HT2200 CHT2200 NotaParts list Key# Description Part Number Qty Engine Group HT2200 RCJ6Y Cutter Group CHT2200 Cutter Group CHT2200 Engine Group CHT2200 RCJ6Y Limited Warranty RedMax Garantie limitée Garantía Limitada Page Komatsu Zenoah America INC