Zenoah CHT2200 manual Symbols on the machine, Emission Control

Page 6

English

3. Warning labels on the machine

(1) Read owner's manual before operating this machine.

		(2) Wear head, eye and ear protection.
	(1)	(3) Handling this machine improperly could result
	(1)	in accidents causing serious injury or death.
		in accidents causing serious injury or death.
		Read this manual carefully and practice using
		the hedge-trimmer until you are fully acquainted
		with all operations and have learned to use it
		correctly.
	(2)	(4) This is extremely sharp and can easily cause
	(2)	cuts.

IMPORTANT

		If warning label peel off or become soiled and
		impossible to read, you should contact the dealer from
	(3)	which you purchased the product to order new labels
	(3)	and affix them in the required location(s).
		and affix them in the required location(s).

		WARNING

	Never modify your brushcutter.
(4)	We won’t warrant the machine, if you use the
	remodeled hedge-trimmer or you don’t observe the
	proper usage written in the manual.

4. Symbols on the machine

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.

(a)The port to refuel the "MIX GASOLINE"

Position:

FUEL TANK CAP

(b)The direction to close the choke

Position:

AIR CLEANER COVER

(c)The direction to open the choke

Position:

AIR CLEANER COVER

■EMISSION CONTROL

An emission control label is located on the engine.

IMPORTANT ENGINE INFORMATION

THIS ENGINE CONFORMS TO 2006 U.S. EPA

REGULATIONS FOR SMALL NONROAD ENGINES.

COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS. 0254CD : EM

ENGINE DISPLACEMENT : 23cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

KOMATSU ZENOAH CO.

RedMax MADE IN JAPAN

6

Image 6

Contents HT2200 CHT2200 Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationModel HT2200 CHT2200 Especificaciohes Emplacement des pieces Situación de las piezasFiche technique Modelo HT2200 CHT2200Symbols on the machine Emission ControlControl DE Emisiones EmplacementPosición Fabricado PORFor safe operation Working ConditionWorking Circumstance Condición DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Trabajo Plan DE TravailAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineCut only materials recommended by Arranque DE LA Máquina Demarrage DU MoteurUtilisation DE LA Machine Empleo DEL ProductoMaintenance If Someone ComesEntretien Consignes de securite Instrucciones de seguridadSI QUELQU’UN S’APPROCHE SI SE Acerca AlguienHandling Fuel Refill after cooling the engineTransportation Manejo DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoBolt Plate Nut Set upBlade Washer Keep Loose Corrugate tube 2 Tie band Throttle cable 4Throttle leverAssemblage Montaje SE6 SE7 SE8 Assemblage Montaje When using Zenoah genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile Zenoah Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitComment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirAbastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteOperation Starting EngineClose Fonctionnement Uso Stopping Engine Adjusting Idling SpeedHOW to USE Idle set screwVis de reglage du ralenti Tornillo de fijación libre Reglage DU Regime DE RalentiAjuste DE LA Velocidad EN Vacío Comment UtiliserHedge Trimming Techniques Vertical cutHorizontal cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoFuel Filter Replacement Plug is Champion RCJ6Y or NGK BPMR7AAIR Filter Spark PlugEntretien Mantenimiento Spark Arrester MA4 Intake AIR Cooling VentBlades Ventilación DE Refrigeración DEL Aire PARE-ETINCELLES MA4Parachispas MA4 Ouïe DE Refroidissement PAR AIR DE AdmisiónSharpening MA7 Procedures to be Performed After Every 100 Hours of USEStorage Reduction GearboxRangement Almacenamiento Troubleshooting guide 10. Guía de localización y solución de problemasGuide de localisation des pannes HT2200 CHT2200 NotaParts list Key# Description Part Number Qty Engine Group HT2200 RCJ6Y Cutter Group CHT2200 Cutter Group CHT2200 Engine Group CHT2200 RCJ6Y Limited Warranty RedMax Garantie limitée Garantía Limitada Page Komatsu Zenoah America INC