Troy-Bilt 682J, E686N, E682L manual Setting Up Non-Powered Attach- ments, Starting The Engine

Page 27

Section 4: Operation

B

A

C

Figure 4-28: Forward Interlock Wiring

A - PTO Power Unit Interlock Harness

B - Forward Interlock Receptacle

C - Attachment Interlock Wire

3.On the PTO Power Unit, unplug the Forward Interlock Wire Harness that leads from the base of the handlebars (A, Figure 4-28) to the receptacle (B) located on the top, right side of the transmission cover.

4.On the Stationary Attachment, locate the interlock wire (C, Figure 4-28) and clean contacts on plug and receptacle (B). This connection enables you to operate the Wheels/Tines/PTO Drive Lever in FORWARD without having to squeeze a Forward Interlock Lever.

5.Connect the plug from the Stationary Attachment (C, Figure 4-28) to the recep- tacle on the PTO Power Unit (B). The connection must be tight.

Setting Up Non-Powered Attach- ments

1.Move the Tines/PTO Clutch Lever (Figure 4-22) to DISENGAGE.

2.Move the Wheel Speed Lever (Figure 4-22) to either SLOW or FAST position To do this, roll the PTO Power Unit while shifting lever until wheels engage.

3.Verify that the Forward Interlock Wire Harness plug at the base of the handle- bars (A, Figure 4-28) is connected to the Forward Interlock Wire Harness recepta- cle (B) on the top right side of the transmission.

Starting The Engine

IMPORTANT: Refer to Cold Weather Operation instructions, in this section, before operating in temperatures below 40oF.

1.Move the Wheels/Tines/PTO Drive Lever into NEUTRAL. To find NEUTRAL (be sure engine is off), push lever down and engage it in FORWARD then tap the lever upward to automatically move into

NEUTRAL .

2.Move the Tines/PTO Clutch Lever into DISENGAGE position.

WARNING

To avoid injury,do not run the engine in an enclosed or poorly vented area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

3.Start Engine. See Starting and Stopping the Engine, in the beginning of this section, for detailed starting informa- tion. Also see the Engine Owner's Manual.

4.For non-powered attachments only test the Forward Interlock Safety System. See Testing the Forward Interlock Safety System, in this section, for a procedure.

Operating Stationary Attachments

1.Move Tines/PTO Clutch Lever (Figure 4-22) into ENGAGE.

2.To apply power to PTO-driven attach- ments, move Wheels/Tines/PTO Lever (Figure 4-22) down to FORWARD position (do not use REVERSE with stationary attachments).

3.To stop the PTO Power Unit, tap the Wheels/Tines/PTO Drive Lever upward into NEUTRAL position.

Operating Non-Powered Attachments (or to Tow Stationary Attachments)

1.To move forward, squeeze and hold one Forward Interlock Lever (Figure 4-30) up against the handlebars, and move the Wheels/Tines/PTO Drive Lever down to

FORWARD.

Figure 4-30: Moving tiller forward: squeeze one Forward Interlock Lever and then move Wheels/Tines/PTO Drive Lever down to FORWARD.

2.To stop forward motion, tap Wheels/Tines/PTO Drive Lever upward into NEUTRAL, then release the Forward Interlock Levers.

3.To stop forward motion in an emergency, release all PTO Power Unit controls (stops engine).

4.To move in reverse, reduce the engine speed then shift the Wheel Speed Lever into SLOW. Move and hold the Wheels/Tines/PTO Drive Lever all the way up. Ensure that the area behind you is clear of all obstacles, before moving the lever into REVERSE.

5.To stop moving in REVERSE, release the Wheels/Tines/PTO Drive Lever.

Stopping the Engine

Move the Engine Throttle Lever to STOP. Turn keyswitch to OFF on electric start models.

Figure 4-29: Block wheels on PTO Power Unit and stationary

 

attachment.

27

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetySafety Keep children and pets awayUse slower wheel, tine and engine speeds Operating Symbols Maintenance and StorageAttach Handlebar Tools/Materials Needed for AssemblyIntroduction Inspect UnitMove Tiller Off Shipping Platform AssemblyRemove the temporary screw J, Figure Check Gear Oil LevelsOil Level Hole Adjust Air Pressure in TiresAttach Engine Throttle Lever and Cable Add Motor Oil to EngineNever bring a gas can near the positive Install Battery CablesConnect the Wire Harness Receptacle To Avoid Personal Injury or Property DamageEngine PTO Attachments FeatureWheels/Tines/PTO Drive Lever Forward Interlock LeversTines/PTO Clutch Lever Features and ControlsHandlebar Height Adjustment Lever Wheel Speed LeverKeyswitch Starter Engine Controls Engine Throttle LeverMove the engine Throttle lever to Stop position Starting and Stopping the Engine Following steps describe how to start and stop the enginePre-Start Checklist Break-In OperationMove engine throttle lever -2 away from Stop OperationMoving the Tiller Forward and Tilling Cold Weather OperationOperating the Tiller Stopping the Engine and TillerMaking Turns Moving the Tiller in ReverseStopping Reverse Motion To Stop the EngineTransporting The Tiller Around Your Property Testing the Forward Interlock Safety SystemHow to Check the Interlock System Loading and Unloading the TillerChanging Belt From LOW Range to High Range Changing Speed BeltsLoading the Tiller Unloading the TillerGo to right side of tiller and finish seating the belt Choosing Wheel Tine SpeedsChanging Belt From High Range to LOW Range Move the Wheels/Tines/PTO Drive Lever into NeutralTo help avoid personal injury, be aware Let the tiller do the workTilling depths Avoid tilling wet, soggy soilTilling up and down slopes Avoid making footprintsSuggested tilling patterns Tilling on slopesTerrace Gardening Clearing the tinesWide-Row Planting Tilling Under CornSoil Enrichment Idea Place Wheel Speed Lever into Free Wheel Figure Removing And Replacing The Tine AttachmentRemoving Tine Attachment Move the tiller to level groundMove the two swing-bolts into Installing the Tine AttachmentSetting Up Stationary Attachments Guide Pin Mounting HoleStopping the Engine Setting Up Non-Powered Attach- mentsStarting The Engine Operating Stationary AttachmentsHours EveryMaintenance Tighten Bolts and NutsTiller Lubrication Checking Gear Oil Levels Transmission Gear Oil MaintenanceChecking the Power Unit Oil Level Checking for Oil LeaksIf the level is incorrect, see Adding or Changing Gear Oil Adding or Changing Gear OilChecking the Tine Attachment Oil Level For Dipsticks With Hot/Cold MarkingsDraining and Filling the Tine Attachment Transmission Adding Gear Oil to PTO Power Unit TransmissionDraining and Filling PTO Power Unit Transmission Adding Gear Oil to the Tine Attachment TransmissionBelt Adjustment Tool Drive Belt MaintenanceMeasuring and Adjusting Drive Belt Tension How to Measure Belt TensionReplacing the Drive Belt Removing the BeltReplacing the Drive Belt Reverse Disc Inspection Reverse Drive System MaintenanceReplacing the Reverse Disc Checking and Adjusting Reverse the Drive SystemInstalling a New Reverse Disc Checking and Adjusting Reverse DiscBolo Tine Maintenance Adjusting Reverse DriveChecking Tines for Wear Replacing Tines Holder Assembly Single Tine ReplacementRemoving and Replacing a Tine Holder Assembly Removing Tine Holder AssemblySpark Plug Maintenance Tine Shaft MaintenanceTire and Wheel Maintenance Air Cleaner MaintenanceInspecting Forward Interlock Wiring System Testing the Forward Interlock Wiring SystemStoring Your Tiller Eccentric Appendix a TroubleshootingTroubleshooting Procedures LinkageTiller Pulls To One Side Wrap-Around Bumper Guard Row Marker Attachment290-258-081 290-257-081 Dozer/Snow Blade AttachmentPage TROY-BILT Tiller Lifetime Limited Warranty

682J, E686N, E682L specifications

The Troy-Bilt brand is widely recognized for its reliable outdoor power equipment, including a line of innovative lawn tractors. Among these, the Troy-Bilt 682J, E686N, and E682L stand out for their exceptional performance and user-friendly features, catering to various lawn care needs.

The Troy-Bilt 682J is a robust lawn tractor designed for efficiency and ease of use. Its 19 HP engine provides ample power for handling various landscaping tasks, while the 42-inch cutting deck allows for a wide cutting path, making quick work of mowing larger yards. The tractor boasts a six-speed transmission, enabling users to select the speed that best suits their mowing conditions. Additionally, the 682J features an ergonomic seat and steering for comfort during extended use, making it a solid choice for homeowners with medium to large properties.

The Troy-Bilt E686N takes things a step further with its advanced technology. This model integrates a 20 HP engine and a larger 46-inch cutting deck, enhancing productivity significantly. The E686N is equipped with a hydrostatic transmission, offering smooth operation and easier control, allowing users to maneuver around obstacles with precision. One of its standout features is the Easy Change Oil Kit, which simplifies maintenance, ensuring that the engine runs smoothly for longer periods. The inclusion of a washout port on the deck makes cleaning effortless, promoting better lawn health and equipment longevity.

For those seeking a more compact option, the Troy-Bilt E682L delivers reliable performance in a smaller package. This model features a 19 HP engine paired with a 38-inch cutting deck, perfect for navigating tighter spaces without compromising power. Its tight turning radius enhances maneuverability, making it ideal for suburban lawns with landscaping features and garden beds. The E682L is designed with user comfort in mind, featuring an adjustable seat and simple controls for intuitive operation.

In summary, the Troy-Bilt 682J, E686N, and E682L represent a dynamic trio of lawn tractors, each catering to various homeowner needs. With powerful engines, efficient cutting decks, and user-friendly features, these models are built to enhance the mowing experience. With their proven reliability and advanced technologies, Troy-Bilt tractors make maintaining a beautiful lawn a manageable task for anyone.
Top Page Image Contents