Troy-Bilt 682J, E686N, E682L manual Maintenance and Storage, Operating Symbols

Page 5

Section 1: Safety

Maintenance and Storage

1.Keep the tiller, attachments and acces- sories in safe working condition.

2.Check all nuts, bolts, and screws at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

3.Never store the tiller with fuel in the fuel tank inside a building where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc.). Allow engine to cool before storing in any enclosure.

4.To reduce the chances of a fire hazard, keep the engine free of grass, leaves, or excessive grease.

5.Store gasoline in a cool, well-ventilated area, safely away from any spark- or flame-producing equipment. Store gasoline in an approved container, safely away from the reach of children.

6.Refer to the Maintenance sections of this Manual and the separate Engine Owner’s Manual for instructions if the tiller is to be stored for an extended period.

7.Never perform maintenance while the engine is running or the spark plug wire is connected, except when specifically instructed to do so.

8.If the fuel tank has to be drained, do this outdoors.

Decals

For your safety and the safety of others, various safety and operational decals are located on your unit (Figure 1).

Keep the decals clean and legible at all times. Contact your local service dealer or the Factory for replacements if any decals are damaged or missing.

Refer to the Parts List for decal locations, descriptions and part numbers.

A) WARNING: Hot Surfaces.

C) WARNING: Operating and

Safety Instructions

Top of the air cleaner housing.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E) Forward

D) Power Unit

 

Interlock

 

Operating

 

Lever (2)

 

Instructions

 

 

F) Engine Stabilization.

B) WARNING: Engine Ignition.

 

Top of fuel tank.

Electric start models only.

 

Figure 1: Location of Safety and Operating Decals. (Briggs & Stratton engine shown)

Operating Symbols

Various symbols (shown here, with word

descriptions) are used on the tiller and engine. FAST Your unit may not have all of the symbols.

 

STOP

 

 

 

SLOW

STOP

CHOKE

CHOKE

ROTATING

 

ON

OFF

 

 

TINES

 

 

 

 

WARNING

TO AVOID SERIOUS INJURY:

•READ THE OWNER’S MANUAL.

•KNOW LOCATIONS AND FUNCTIONS OF ALL CONTROLS.

•KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.

•NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER.

•SHUT OFF ENGINE AND DISCONNECT SPARK PLUG WIRE BEFORE MANUALLY UNCLOG- GING TINES OR MAKING REPAIRS.

•KEEP BYSTANDERS AWAY FROM MACHINE.

•KEEP AWAY FROM ROTATING PARTS.

•USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetyUse slower wheel, tine and engine speeds SafetyKeep children and pets away Operating Symbols Maintenance and StorageIntroduction Tools/Materials Needed for AssemblyInspect Unit Attach HandlebarMove Tiller Off Shipping Platform AssemblyRemove the temporary screw J, Figure Check Gear Oil LevelsAttach Engine Throttle Lever and Cable Adjust Air Pressure in TiresAdd Motor Oil to Engine Oil Level HoleConnect the Wire Harness Receptacle Install Battery CablesTo Avoid Personal Injury or Property Damage Never bring a gas can near the positiveWheels/Tines/PTO Drive Lever PTO Attachments FeatureForward Interlock Levers EngineHandlebar Height Adjustment Lever Features and ControlsWheel Speed Lever Tines/PTO Clutch LeverMove the engine Throttle lever to Stop position Keyswitch StarterEngine Controls Engine Throttle Lever Pre-Start Checklist Following steps describe how to start and stop the engineBreak-In Operation Starting and Stopping the EngineMove engine throttle lever -2 away from Stop OperationOperating the Tiller Cold Weather OperationStopping the Engine and Tiller Moving the Tiller Forward and TillingStopping Reverse Motion Moving the Tiller in ReverseTo Stop the Engine Making TurnsHow to Check the Interlock System Testing the Forward Interlock Safety SystemLoading and Unloading the Tiller Transporting The Tiller Around Your PropertyLoading the Tiller Changing Speed BeltsUnloading the Tiller Changing Belt From LOW Range to High RangeChanging Belt From High Range to LOW Range Choosing Wheel Tine SpeedsMove the Wheels/Tines/PTO Drive Lever into Neutral Go to right side of tiller and finish seating the beltTilling depths Let the tiller do the workAvoid tilling wet, soggy soil To help avoid personal injury, be awareSuggested tilling patterns Avoid making footprintsTilling on slopes Tilling up and down slopesTerrace Gardening Clearing the tinesSoil Enrichment Idea Wide-Row PlantingTilling Under Corn Removing Tine Attachment Removing And Replacing The Tine AttachmentMove the tiller to level ground Place Wheel Speed Lever into Free Wheel FigureSetting Up Stationary Attachments Installing the Tine AttachmentGuide Pin Mounting Hole Move the two swing-bolts intoStarting The Engine Setting Up Non-Powered Attach- mentsOperating Stationary Attachments Stopping the EngineHours EveryTiller Lubrication MaintenanceTighten Bolts and Nuts Checking the Power Unit Oil Level Transmission Gear Oil MaintenanceChecking for Oil Leaks Checking Gear Oil LevelsChecking the Tine Attachment Oil Level Adding or Changing Gear OilFor Dipsticks With Hot/Cold Markings If the level is incorrect, see Adding or Changing Gear OilDraining and Filling PTO Power Unit Transmission Adding Gear Oil to PTO Power Unit TransmissionAdding Gear Oil to the Tine Attachment Transmission Draining and Filling the Tine Attachment TransmissionMeasuring and Adjusting Drive Belt Tension Drive Belt MaintenanceHow to Measure Belt Tension Belt Adjustment ToolReplacing the Drive Belt Replacing the Drive BeltRemoving the Belt Reverse Disc Inspection Reverse Drive System MaintenanceInstalling a New Reverse Disc Checking and Adjusting Reverse the Drive SystemChecking and Adjusting Reverse Disc Replacing the Reverse DiscChecking Tines for Wear Bolo Tine MaintenanceAdjusting Reverse Drive Removing and Replacing a Tine Holder Assembly Single Tine ReplacementRemoving Tine Holder Assembly Replacing Tines Holder AssemblyTire and Wheel Maintenance Tine Shaft MaintenanceAir Cleaner Maintenance Spark Plug MaintenanceStoring Your Tiller Inspecting Forward Interlock Wiring SystemTesting the Forward Interlock Wiring System Troubleshooting Procedures Appendix a TroubleshootingLinkage EccentricTiller Pulls To One Side 290-258-081 290-257-081 Row Marker AttachmentDozer/Snow Blade Attachment Wrap-Around Bumper GuardPage TROY-BILT Tiller Lifetime Limited Warranty

682J, E686N, E682L specifications

The Troy-Bilt brand is widely recognized for its reliable outdoor power equipment, including a line of innovative lawn tractors. Among these, the Troy-Bilt 682J, E686N, and E682L stand out for their exceptional performance and user-friendly features, catering to various lawn care needs.

The Troy-Bilt 682J is a robust lawn tractor designed for efficiency and ease of use. Its 19 HP engine provides ample power for handling various landscaping tasks, while the 42-inch cutting deck allows for a wide cutting path, making quick work of mowing larger yards. The tractor boasts a six-speed transmission, enabling users to select the speed that best suits their mowing conditions. Additionally, the 682J features an ergonomic seat and steering for comfort during extended use, making it a solid choice for homeowners with medium to large properties.

The Troy-Bilt E686N takes things a step further with its advanced technology. This model integrates a 20 HP engine and a larger 46-inch cutting deck, enhancing productivity significantly. The E686N is equipped with a hydrostatic transmission, offering smooth operation and easier control, allowing users to maneuver around obstacles with precision. One of its standout features is the Easy Change Oil Kit, which simplifies maintenance, ensuring that the engine runs smoothly for longer periods. The inclusion of a washout port on the deck makes cleaning effortless, promoting better lawn health and equipment longevity.

For those seeking a more compact option, the Troy-Bilt E682L delivers reliable performance in a smaller package. This model features a 19 HP engine paired with a 38-inch cutting deck, perfect for navigating tighter spaces without compromising power. Its tight turning radius enhances maneuverability, making it ideal for suburban lawns with landscaping features and garden beds. The E682L is designed with user comfort in mind, featuring an adjustable seat and simple controls for intuitive operation.

In summary, the Troy-Bilt 682J, E686N, and E682L represent a dynamic trio of lawn tractors, each catering to various homeowner needs. With powerful engines, efficient cutting decks, and user-friendly features, these models are built to enhance the mowing experience. With their proven reliability and advanced technologies, Troy-Bilt tractors make maintaining a beautiful lawn a manageable task for anyone.
Top Page Image Contents