Troy-Bilt 682J, E686N, E682L Install Battery Cables, To Avoid Personal Injury or Property Damage

Page 10

Section 2: Assembly

ASSEMBLING THE ELECTRIC START SYSTEM

The following steps explain how to install and charge the battery on electric start tillers. For your safety, follow all steps and observe all accompanying safety messages. Section 5 contains other general battery maintenance and recharging instructions.

DANGER

Battery produces explosive gases.

•Keep away sparks, flames, and cigarettes.

•Ventilate area when charging or using battery in an enclosed space.

•Make sure battery vent tube is always open after battery is filled with acid.

WARNING

Remove metal jewelry before working near the battery or near the electrical system. Failure to comply may cause a short circuit, resulting in electrical burns, a shock, or battery gas explosion.

NOTE: If the battery is put into service after the date shown on the top of the battery, charge for a minimum of one hour at 6-10 amps. Refer to the Maintenence section of this manual for more detailed instructions regarding proper battery charging procedure

1.Use a 5/8" long screw (K, Figure 2-18) and 1/4-20 hex nut (L) to connect the positive (+) battery cable (B) to the positive (marked +) battery post (C). Make sure that this is the cable on the left side, with one end attached to the solenoid (D).

2.Slide the black rubber boot (E) com- pletely over the battery post and cable connector.

3.Use a 5/8" long screw and 1/4-20 hex nut to connect the negative (-) battery cable (F) to the negative (marked -) battery post (G) and secure with screw

(H) and nut (I).

4.Slide the black rubber boot (J) com- pletely over the battery post and cable connector.

Assembly is complete for electric start tillers. See Section 3, Controls for information on tiller controls.

DANGER

To Avoid Personal Injury or Property Damage:

•Do not touch positive battery terminal and any surrounding metal objects with tools, jewelry or other metal items. Failure to comply could cause a short circuit leading to electrical burns or explosion of battery gases.

•Never bring a gas can near the positive

(+)battery terminal. A short circuit could occur leading to an explosion of the gasoline or the battery gases. Always fill the engine fuel tank from the front or side of the engine.

DANGER

Never jump start the battery with a vehicle battery or charging system. This may produce a battery explosion, causing acid or electrical burns.

STEP 1: Connect the Wire Harness Receptacle

1.Before installing the battery and its hold-down clamp, insert the plastic wire harness receptacle (A, Figure 2-18) into the prongs of the keyswitch (M) located on the hold-down clamp.

2.Remove the ignition keys from the keyswitch and store them safely away. Do not insert the key into the keyswitch until you complete this section and read Section 3, Controls.

STEP 2: Install the

Battery Cables

NOTE: The cable terminals should be toward the rear (keyswitch side) of the battery posts.

H

K

G (-)

J

I

C (+)

B E LF

M

A

D

Figure 2-18: Battery cable assembly.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Table of Contents Safety Safety Alert SymbolKeep children and pets away SafetyUse slower wheel, tine and engine speeds Maintenance and Storage Operating SymbolsInspect Unit Tools/Materials Needed for AssemblyIntroduction Attach HandlebarAssembly Move Tiller Off Shipping PlatformCheck Gear Oil Levels Remove the temporary screw J, FigureAdd Motor Oil to Engine Adjust Air Pressure in TiresAttach Engine Throttle Lever and Cable Oil Level HoleTo Avoid Personal Injury or Property Damage Install Battery CablesConnect the Wire Harness Receptacle Never bring a gas can near the positiveForward Interlock Levers PTO Attachments FeatureWheels/Tines/PTO Drive Lever EngineWheel Speed Lever Features and ControlsHandlebar Height Adjustment Lever Tines/PTO Clutch LeverEngine Controls Engine Throttle Lever Keyswitch StarterMove the engine Throttle lever to Stop position Break-In Operation Following steps describe how to start and stop the enginePre-Start Checklist Starting and Stopping the EngineOperation Move engine throttle lever -2 away from StopStopping the Engine and Tiller Cold Weather OperationOperating the Tiller Moving the Tiller Forward and TillingTo Stop the Engine Moving the Tiller in ReverseStopping Reverse Motion Making TurnsLoading and Unloading the Tiller Testing the Forward Interlock Safety SystemHow to Check the Interlock System Transporting The Tiller Around Your PropertyUnloading the Tiller Changing Speed BeltsLoading the Tiller Changing Belt From LOW Range to High RangeMove the Wheels/Tines/PTO Drive Lever into Neutral Choosing Wheel Tine SpeedsChanging Belt From High Range to LOW Range Go to right side of tiller and finish seating the beltAvoid tilling wet, soggy soil Let the tiller do the workTilling depths To help avoid personal injury, be awareTilling on slopes Avoid making footprintsSuggested tilling patterns Tilling up and down slopesClearing the tines Terrace GardeningTilling Under Corn Wide-Row PlantingSoil Enrichment Idea Move the tiller to level ground Removing And Replacing The Tine AttachmentRemoving Tine Attachment Place Wheel Speed Lever into Free Wheel FigureGuide Pin Mounting Hole Installing the Tine AttachmentSetting Up Stationary Attachments Move the two swing-bolts intoOperating Stationary Attachments Setting Up Non-Powered Attach- mentsStarting The Engine Stopping the EngineEvery HoursTighten Bolts and Nuts MaintenanceTiller Lubrication Checking for Oil Leaks Transmission Gear Oil MaintenanceChecking the Power Unit Oil Level Checking Gear Oil LevelsFor Dipsticks With Hot/Cold Markings Adding or Changing Gear OilChecking the Tine Attachment Oil Level If the level is incorrect, see Adding or Changing Gear OilAdding Gear Oil to the Tine Attachment Transmission Adding Gear Oil to PTO Power Unit TransmissionDraining and Filling PTO Power Unit Transmission Draining and Filling the Tine Attachment TransmissionHow to Measure Belt Tension Drive Belt MaintenanceMeasuring and Adjusting Drive Belt Tension Belt Adjustment ToolRemoving the Belt Replacing the Drive BeltReplacing the Drive Belt Reverse Drive System Maintenance Reverse Disc InspectionChecking and Adjusting Reverse Disc Checking and Adjusting Reverse the Drive SystemInstalling a New Reverse Disc Replacing the Reverse DiscAdjusting Reverse Drive Bolo Tine MaintenanceChecking Tines for Wear Removing Tine Holder Assembly Single Tine ReplacementRemoving and Replacing a Tine Holder Assembly Replacing Tines Holder AssemblyAir Cleaner Maintenance Tine Shaft MaintenanceTire and Wheel Maintenance Spark Plug MaintenanceTesting the Forward Interlock Wiring System Inspecting Forward Interlock Wiring SystemStoring Your Tiller Linkage Appendix a TroubleshootingTroubleshooting Procedures EccentricTiller Pulls To One Side Dozer/Snow Blade Attachment Row Marker Attachment290-258-081 290-257-081 Wrap-Around Bumper GuardPage TROY-BILT Tiller Lifetime Limited Warranty

682J, E686N, E682L specifications

The Troy-Bilt brand is widely recognized for its reliable outdoor power equipment, including a line of innovative lawn tractors. Among these, the Troy-Bilt 682J, E686N, and E682L stand out for their exceptional performance and user-friendly features, catering to various lawn care needs.

The Troy-Bilt 682J is a robust lawn tractor designed for efficiency and ease of use. Its 19 HP engine provides ample power for handling various landscaping tasks, while the 42-inch cutting deck allows for a wide cutting path, making quick work of mowing larger yards. The tractor boasts a six-speed transmission, enabling users to select the speed that best suits their mowing conditions. Additionally, the 682J features an ergonomic seat and steering for comfort during extended use, making it a solid choice for homeowners with medium to large properties.

The Troy-Bilt E686N takes things a step further with its advanced technology. This model integrates a 20 HP engine and a larger 46-inch cutting deck, enhancing productivity significantly. The E686N is equipped with a hydrostatic transmission, offering smooth operation and easier control, allowing users to maneuver around obstacles with precision. One of its standout features is the Easy Change Oil Kit, which simplifies maintenance, ensuring that the engine runs smoothly for longer periods. The inclusion of a washout port on the deck makes cleaning effortless, promoting better lawn health and equipment longevity.

For those seeking a more compact option, the Troy-Bilt E682L delivers reliable performance in a smaller package. This model features a 19 HP engine paired with a 38-inch cutting deck, perfect for navigating tighter spaces without compromising power. Its tight turning radius enhances maneuverability, making it ideal for suburban lawns with landscaping features and garden beds. The E682L is designed with user comfort in mind, featuring an adjustable seat and simple controls for intuitive operation.

In summary, the Troy-Bilt 682J, E686N, and E682L represent a dynamic trio of lawn tractors, each catering to various homeowner needs. With powerful engines, efficient cutting decks, and user-friendly features, these models are built to enhance the mowing experience. With their proven reliability and advanced technologies, Troy-Bilt tractors make maintaining a beautiful lawn a manageable task for anyone.
Top Page Image Contents