Troy-Bilt 682J, E686N, E682L manual Testing the Forward Interlock Safety System

Page 18

Section 4: Operation

4.When the turn is complete, shift to NEUTRAL and lower the handlebars. Move Tines/PTO Clutch Lever back to ENGAGE position and resume forward operation.

Transporting The Tiller Around Your Property

When the engine is running, the tiller’s powered wheels make moving the tiller to and from the garden easy. If the engine is not running set the Wheel Speed Lever to FREEWHEEL position to roll the tiller to another location.

WARNING

To help avoid personal injury from revolving tines, always put the Tines/PTO Clutch Lever in DISENGAGE position before transporting, loading, or unloading tiller.

1.Place the Tines/PTO Clutch Lever in DISENGAGE position.

2.Move Depth Regulator Lever down all the way into the Travel setting.

3.If using engine power, move Wheel Speed Lever to either SLOW or FAST, and use the Wheels/Tines/PTO Drive Lever to drive the wheels.

4.If the engine is stopped, move Wheel Speed Lever to FREEWHEEL, and manually push tiller.

Testing the Forward

Interlock Safety System

The Forward Interlock Safety System is designed to shut the tiller engine off immediately if you lose control and cannot stop moving FORWARD by shifting the Wheels/Tines/PTO Drive Lever into NEUTRAL. When you release both Forward Interlock Levers, they send ground to the ignition system thereby stopping the engine. Squeezing one or both levers up against the handlebars enables the ignition system; therefore, you must squeeze at least one lever whenever the Wheels/Tines/PTO Drive Lever is engaged in FORWARD.

IMPORTANT: The interlock system also prevents the engine from starting if the Wheels/Tines/PTO Drive Lever is engaged in FORWARD.

DANGER

The Forward Interlock Safety System is designed for the operator’s safety. Do not disconnect or attempt to defeat the purpose of the system. If the system malfunctions, immediately contact your local authorized dealer or the TROY-BILT Technical Service Depart- ment for assistance. Do not use the tiller or the PTO power unit until the Forward Interlock Safety System is functioning properly. Always test the system before using the tiller or PTO power unit.

How to Check the Interlock System

The Forward Interlock System has an electro-mechanical design, and so is subject to normal wear and possible mal- function. Check the system for proper operation each time prior to using the tiller or PTO power unit.

Figure 4-6: Plug and receptacle of Forward Interlock Safety System must be securely connected.

To test the Forward Interlock System:

1.Move tiller outside to level ground. Remove any obstacles.

2.Check that the Forward Interlock wire harness plug, at the bottom of the handle- bars (Figure 4-6), is securely connected to the receptacle on the top, right side of the transmission.

3.Move Wheel Speed Lever (Figure 4-2) to SLOW position and move Tines/ PTO Clutch Lever to DISENGAGE.

4.Start engine as described under Starting and Stopping the Engine, in this section. Set engine throttle lever to SLOW, and let engine warm up.

5.Squeeze and hold just one of the Forward Interlock Levers against the handlebar grip while moving the Wheels/ Tines/ PTO Drive Lever down to FORWARD (Figure 4-3). As the tiller moves forward, release the Forward Inter- lock Lever briefly. The engine should start to stall out if the interlock system is working properly. If it does start to stall, quickly squeeze the lever up against the handlebar grip, and then return the Wheels/ Tines/ PTO Drive Lever to NEUTRAL. Repeat this test to check that the engine begins to stall out when the other Forward Interlock Lever is released.

6.If the engine does not begin to shut off when either Forward Interlock lever is released, shut the engine off, remove the key (if electric start), and do not operate the tiller or PTO power unit until the system has been repaired and is func- tioning properly.

IMPORTANT: To avoid possible damage to the Forward Interlock Safety system, do not use high-pressure sprays near the wire harness receptacle or neutral plunger assembly.

Loading and Unloading the Tiller

The following provides information on tiller loading, unloading, and requirements before loading and unloading the tiller. Read the following instructions carefully before attempting to load or unload your tiller.

Before Loading or Unloading the Tiller

•Ramps must be strong enough to support the combined weight of the tiller and handlers. They should provide good traction to prevent slipping; they should have side rails to guide the tiller along the ramps; and they should have a locking device to secure them to the vehicle.

•Handlers should wear sturdy footwear that will help to prevent slipping.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator’s Manual Table of Contents Safety Safety Alert SymbolSafety Keep children and pets awayUse slower wheel, tine and engine speeds Maintenance and Storage Operating SymbolsInspect Unit Tools/Materials Needed for AssemblyIntroduction Attach HandlebarAssembly Move Tiller Off Shipping PlatformCheck Gear Oil Levels Remove the temporary screw J, FigureAdd Motor Oil to Engine Adjust Air Pressure in TiresAttach Engine Throttle Lever and Cable Oil Level HoleTo Avoid Personal Injury or Property Damage Install Battery CablesConnect the Wire Harness Receptacle Never bring a gas can near the positiveForward Interlock Levers PTO Attachments FeatureWheels/Tines/PTO Drive Lever EngineWheel Speed Lever Features and ControlsHandlebar Height Adjustment Lever Tines/PTO Clutch LeverKeyswitch Starter Engine Controls Engine Throttle LeverMove the engine Throttle lever to Stop position Break-In Operation Following steps describe how to start and stop the enginePre-Start Checklist Starting and Stopping the EngineOperation Move engine throttle lever -2 away from StopStopping the Engine and Tiller Cold Weather OperationOperating the Tiller Moving the Tiller Forward and TillingTo Stop the Engine Moving the Tiller in ReverseStopping Reverse Motion Making TurnsLoading and Unloading the Tiller Testing the Forward Interlock Safety SystemHow to Check the Interlock System Transporting The Tiller Around Your PropertyUnloading the Tiller Changing Speed BeltsLoading the Tiller Changing Belt From LOW Range to High RangeMove the Wheels/Tines/PTO Drive Lever into Neutral Choosing Wheel Tine SpeedsChanging Belt From High Range to LOW Range Go to right side of tiller and finish seating the beltAvoid tilling wet, soggy soil Let the tiller do the workTilling depths To help avoid personal injury, be awareTilling on slopes Avoid making footprintsSuggested tilling patterns Tilling up and down slopesClearing the tines Terrace GardeningWide-Row Planting Tilling Under CornSoil Enrichment Idea Move the tiller to level ground Removing And Replacing The Tine AttachmentRemoving Tine Attachment Place Wheel Speed Lever into Free Wheel FigureGuide Pin Mounting Hole Installing the Tine AttachmentSetting Up Stationary Attachments Move the two swing-bolts intoOperating Stationary Attachments Setting Up Non-Powered Attach- mentsStarting The Engine Stopping the EngineEvery HoursMaintenance Tighten Bolts and NutsTiller Lubrication Checking for Oil Leaks Transmission Gear Oil MaintenanceChecking the Power Unit Oil Level Checking Gear Oil LevelsFor Dipsticks With Hot/Cold Markings Adding or Changing Gear OilChecking the Tine Attachment Oil Level If the level is incorrect, see Adding or Changing Gear OilAdding Gear Oil to the Tine Attachment Transmission Adding Gear Oil to PTO Power Unit TransmissionDraining and Filling PTO Power Unit Transmission Draining and Filling the Tine Attachment TransmissionHow to Measure Belt Tension Drive Belt MaintenanceMeasuring and Adjusting Drive Belt Tension Belt Adjustment ToolReplacing the Drive Belt Removing the BeltReplacing the Drive Belt Reverse Drive System Maintenance Reverse Disc InspectionChecking and Adjusting Reverse Disc Checking and Adjusting Reverse the Drive SystemInstalling a New Reverse Disc Replacing the Reverse DiscBolo Tine Maintenance Adjusting Reverse DriveChecking Tines for Wear Removing Tine Holder Assembly Single Tine ReplacementRemoving and Replacing a Tine Holder Assembly Replacing Tines Holder AssemblyAir Cleaner Maintenance Tine Shaft MaintenanceTire and Wheel Maintenance Spark Plug MaintenanceInspecting Forward Interlock Wiring System Testing the Forward Interlock Wiring SystemStoring Your Tiller Linkage Appendix a TroubleshootingTroubleshooting Procedures EccentricTiller Pulls To One Side Dozer/Snow Blade Attachment Row Marker Attachment290-258-081 290-257-081 Wrap-Around Bumper GuardPage TROY-BILT Tiller Lifetime Limited Warranty

682J, E686N, E682L specifications

The Troy-Bilt brand is widely recognized for its reliable outdoor power equipment, including a line of innovative lawn tractors. Among these, the Troy-Bilt 682J, E686N, and E682L stand out for their exceptional performance and user-friendly features, catering to various lawn care needs.

The Troy-Bilt 682J is a robust lawn tractor designed for efficiency and ease of use. Its 19 HP engine provides ample power for handling various landscaping tasks, while the 42-inch cutting deck allows for a wide cutting path, making quick work of mowing larger yards. The tractor boasts a six-speed transmission, enabling users to select the speed that best suits their mowing conditions. Additionally, the 682J features an ergonomic seat and steering for comfort during extended use, making it a solid choice for homeowners with medium to large properties.

The Troy-Bilt E686N takes things a step further with its advanced technology. This model integrates a 20 HP engine and a larger 46-inch cutting deck, enhancing productivity significantly. The E686N is equipped with a hydrostatic transmission, offering smooth operation and easier control, allowing users to maneuver around obstacles with precision. One of its standout features is the Easy Change Oil Kit, which simplifies maintenance, ensuring that the engine runs smoothly for longer periods. The inclusion of a washout port on the deck makes cleaning effortless, promoting better lawn health and equipment longevity.

For those seeking a more compact option, the Troy-Bilt E682L delivers reliable performance in a smaller package. This model features a 19 HP engine paired with a 38-inch cutting deck, perfect for navigating tighter spaces without compromising power. Its tight turning radius enhances maneuverability, making it ideal for suburban lawns with landscaping features and garden beds. The E682L is designed with user comfort in mind, featuring an adjustable seat and simple controls for intuitive operation.

In summary, the Troy-Bilt 682J, E686N, and E682L represent a dynamic trio of lawn tractors, each catering to various homeowner needs. With powerful engines, efficient cutting decks, and user-friendly features, these models are built to enhance the mowing experience. With their proven reliability and advanced technologies, Troy-Bilt tractors make maintaining a beautiful lawn a manageable task for anyone.
Top Page Image Contents