Control/Monitor Functions | Crown Audio IQ P.I.P.-DSP specification

IQ–P.I.P.–DSPProgrammable Input Processor with DSP for IQ Systems

parameters are used here such as threshold, attack time, etc. Next, the output limiter is processed through control- lable polarity inverters. The last processing section is an output muter after which the signal is sent to the main am- plifier for voltage and current amplification.

All parameters are continuously controllable via the IQ System or can be set and will continue to operate.

5.2 Control/Monitor Functions

5.2.1 Audio Signals

In addition to controlling the audio input level and polarity, the IQ–P.I.P.–DSPcan turn on/off the high-voltage power supplies. These functions are controlled using ports on the 6811 microprocessor and some external support cir- cuitry. The audio level is controlled by the 6811 micropro- cessor through a digitally controlled analog attenuator.

The audio signals that are monitored are the input to the P.I.P. and the output of the amplifier. These signals enter the P.I.P. and are fed into a precision peak detector which insures that instantaneous signal peaks are not “missed” by the P.I.P. The detector outputs are then fed through a multiplexer into a logarithmic conversion circuit for dy- namic range scaling. The output of this circuit is then fed into the A/D converter on the 6811 microprocessor, where the signal is converted and sent to the host computer via the Crown Bus.

5.2.2 Status Signals

The status signals that are monitored are ODEP level, IOC status and VCC status. These signals enter the P.I.P., pass through a buffer stage, and are fed into the A/D converter on the 6811 microprocessor. The signals are then con- verted and sent to the host computer via the Crown Bus.

5.2.3 DSPI Control

The DSPI LED flashes whenever a valid IQ command has been received and can be forced to stay on to facilitate diagnosis of Crown Bus wiring problems.

5.3 IQ System Communications

The IQ–P.I.P.–DSPcommunicates with the host computer via the Crown Bus. Connections to the Crown Bus are made via the 4 and 5-pin locking DIN connectors on the rear panel. IQ commands entering the P.I.P. are fed into an input receiver circuit that converts the 20 mA current loop signal into a standard logic signal that the 6811 mi- croprocessor can understand. This signal is also passed directly to the Crown Bus for output where it is passed on to the remainder of the loop. Data sent in response to IQ commands is also sent through the Crown Bus output where it passes through the remainder of the loop and back to the host computer. A “drop out” relay is also present which makes a physical contact between the Crown Bus input and output connectors in the event of a power failure. This means that as long as the Crown Bus cables are connected to the P.I.P., the Crown Bus will re- main unbroken—even if power to the P.I.P. is lost.

5.4 Microprocessors and Reset Switch

The “brains” of the IQ–P.I.P.–DSPare contained in its two microprocessors. A Motorola 6811 interprets commands received from the Crown Bus and responds accordingly. A Motorola 56002 manages all DSP functions. The memory of both processors is backed up with EEPROM. The IQ–P.I.P.–DSPis designed to provide an “automatic reset” in the event of a power failure, but the rear reset switch has also been added. Pressing this switch restores all P.I.P. settings to the “user defaults” if it is pressed for less than 2 seconds or to the factory defaults if it is pressed for more than 2 seconds. The only exception is the initialization data which can only be changed with IQ System software on the host computer.

INPUT	INPUT					ODEP CONSER-				INPUT PROTEC-
ATTENUATOR	COMPRESSOR					VATION LIMITER				TION LIMITER
ATTENUATION	ON/OFF	THRESHOLD ATTACK TIME	RELEASE TIME RATIO				ON/OFF TRIGGER LEVEL	CONSERVATION AMOUNT RELEASE TIME
	FLTR	FLTR	FLTR	FLTR			FLTR	FLTR	FLTR	FLTR	SIGNAL
	1	2	3		4		5	6	7	8	DELAY
				ON/OFF	FILTER TYPE	FILTER Q	FREQUENCY FILTER GAIN				DELAY
							FILTER

DAISY CHAIN

OUTPUT

MAIN

AMPLIFIER

	OUTPUT	POLARITY	OUTPUT
ON/OFF	LIMITER	INVERTER	MUTER


	THRESHOLD ATTACK TIME RELEASE TIME	INVERT / NORMAL	MUTE / UNMUTE

IQ-P.IP.-DP AMPLIFIER

Fig. 5.2 IQ–P.I.P.–DSP Audio Signal Flow Block Diagram

Page 22

Reference Manual