Tascam CD-RW700 owner manual Recording-Advanced recording

Page 19

4 • Recording—Advanced recording

However, during recording there are fewer options available (obviously, the unit cannot see into the future and know how much time remains of the track which is being currently recorded!).

When in record or record ready mode, repeated presses of the DISPLAY key (A or 6) cycle between displaying the remaining time left for recording on the disc (TOTAL REMAIN) and the elapsed time of the track currently being recorded (no indica- tor lit).

When playback is stopped at the start of a recordable disc, there are only two options available: TOTAL (the total time recorded so far on the disc) and TOTAL REMAIN (the total time available on the disc for fur- ther recording).

4.2.3Manual track division

It is possible to divide the recording into tracks “on the fly” while recording.

While recording is taking place, press the RECORD key (K or E) . The current track number is incre- mented by one.

For details of automatic track division while record- ing, see 4.3.2, “Automatic track division”.

NOTE

According to the “Red Book” (the specification for audio CDs), a track cannot be less than four seconds in length, and there can be a maximum of 99 tracks on an audio CD. Bear these limitations in mind when adding track divisions.

4.2.4Restricting the number of tracks

When making a recording using the CD-RW700, it is possible to restrict the number of tracks that may be recorded at one time. This applies whether the tracks are being divided manually, as described above (4.2.3, “Manual track division”) or being divided automatically (4.3.2, “Automatic track division”).

At any time within record or record ready mode, turn the MULTI JOG control B or use the SKIP keys I.

This sets the number of remaining tracks, as shown to the right of the time display. The maximum num- ber here is limited by the standard limit of 99 tracks, and the number of tracks currently recorded. In other words, if 8 tracks have already been recorded on the disc, the maximum value that can be set here is 91 (91+8=99). If 49 tracks have already been recorded on the disc, the maximum value that can be set here is 50 (49+50=99).

Every time a track division is made, the number shown at the right of the display goes down by one. When the number shown is 1, and a track division is made, the display shows PMA Writing and the unit enters stop mode.

The number of remaining tracks can be changed dur- ing recording using the MULTI JOG control.

4.2.5Full disc

If recording a long program, and the number of tracks has not been restricted, when there is no space remaining on the disc for recording, as shown by the time display (see 4.2.2, “Time display while record- ing”), just before the end of the disc is reached, the unit starts a fade-out over a few seconds (the display shows FADE OUT).

When the fade-out has finished, the display shows Disc Full!! for a few seconds, and the unit then goes into stop mode (the display shows PMA Writing).

If the disc is a CD-RW, the final track can be erased, if required (see 5.2.1, “Erasing tracks”) and the disc then finalized. If the disc is a CD-R, it must be final- ized prior to use (see 5.1, “Finalizing”).

4.3 Advanced recording

These sections cover more advanced recording techniques.

4.3.1Synchronized recording

Synchronized recording means that recording will begin automatically when a signal is received, and will stop when the signal ends.

To enable or disable synchronized recording:

1A recordable disc must be loaded.

2With the unit in record ready or record mode, press the SYNC REC key (Lor F).

The display shows SYNC ON briefly, and then changes to the track and time display. When synchronized recording is enabled, the SYNC indicator lights in the display.

The SYNC REC key is also used to turn off syn- chronized recording (the display briefly shows SYNC OFF and then returns to the track and time display).

The signal level which may be used with synchro- nized recording operations (here called the “trigger level” or “threshold”) is set as below:

TASCAM CD-RW700 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents CD-RW700 Do not cut off the mains plug from this equipment Important Safety PrecautionsImportant Safety Instructions Pour le Canada For CanadaTable of Contents About CD-R and CD-RW discs IntroductionEnvironmental considerations Introduction-FinalizingFinalizing Unpacking the CD-RW700Handling of compact discs Introduction-Environmental considerationsBeware of condensation Never use a stabilizer or printable discsDimensional drawing Default settingsRecommended media Features of the CD-RW700 Front panel Features of the CD-RW700-Front panelRemote control unit Features of the CD-RW700-Rear panelRear panel Timer operations Features of the CD-RW700-ConnectionsConnections Setting the timer Features of the CD-RW700-Timer operationsUsing the timer Track search Playback operationsSimple playback operations Time display modesProgrammed order playback Playback operations-Programmed order playbackRepeat play Input monitoring Signal volumeRecording Input selectionTime display while recording Recording-Basic recordingBasic recording Playing back tracksAdvanced recording Recording-Advanced recording66, and -72dB Automatic track division Automatic track increment Digital directFade-in and fade-out Recording-RehearsalRehearsal Rec mute functionPress the Rhsl key 4 so that the display shows Waiting Sync Rehearsal for synchronized recordingRehearsal for track division Erasing tracks After recordingErasing 1 Unfinalizing CD-RW discsErasing a whole disc After recording-ErasingRefreshing a disc Troubleshooting Reference and specificationsSpecifications

CD-RW700 specifications

The Tascam CD-RW700 is a professional-grade audio CD recorder designed for serious musicians, sound engineers, and audio enthusiasts. With a robust build quality and a multitude of features, this unit is well-suited for both studio and live settings.

One of the standout features of the CD-RW700 is its ability to record, erase, and re-record on CD-R and CD-RW media. This flexibility allows users to create high-quality CDs for various applications, from music albums to archival projects. The CD-RW700 employs a sophisticated digital-to-analog converter, ensuring pristine sound quality during playback and recording.

The unit supports a variety of recording formats, including CD-DA, WAV, and MP3, catering to different audio needs. The high-speed dubbing function allows for rapid copying of CDs, making it ideal for situations where time is of the essence. Additionally, the device features a high-quality pitch control and signal processing function, enabling users to adjust the pitch and tempo of recordings with ease.

Equipped with a clear LCD display, the CD-RW700 provides users with real-time feedback on recording levels, time elapsed, and remaining time. This user-friendly interface enhances the overall experience, allowing for straightforward navigation and operation. The built-in metronome and tuner serve as useful tools for musicians during recording sessions.

Connectivity is another strong point of the CD-RW700. It features balanced XLR inputs and outputs, as well as unbalanced RCA connections, ensuring compatibility with a wide range of audio equipment. The inclusion of a coaxial digital input and output further enhances its versatility, allowing for high-quality digital transfers.

The CD-RW700 also supports various anti-shock technologies, ensuring smooth playback without interruptions during live performances or sensitive recordings. This reliability makes it an excellent choice for both professional studios and home setups.

In conclusion, the Tascam CD-RW700 combines advanced recording technologies with comprehensive features, making it an essential tool for anyone looking to produce high-quality audio CDs. Its robust design, user-friendly interface, and versatile connectivity options position it as a leading choice in the realm of CD recording equipment. Whether you’re a musician, producer, or sound technician, the Tascam CD-RW700 offers the reliability and performance needed to meet demanding audio requirements.
Top Page Image Contents