Tascam CD-RW700 owner manual After recording-Erasing, Erasing a whole disc, Refreshing a disc

Page 27

3Turn the MULTI JOG control or use the SKIP keys to change the number of the first track to be erased. The highest value that this number can take is the last track recorded (e.g. if 17 tracks have been recorded on the disc, 17- 17 means that the last track only, 17, will be erased). The lowest value that this number can take is 2 (if this number was 1, the whole disc would be erased, as described below).

4If you do not want to proceed with the erase operation, press any other key (such as the STOP key).

NOTE

If only one track has been recorded on the disc, only the “erase disc” option (5.2.2, “Erasing a whole disc”) is available.

5When the range of tracks to be erased has been selected, press the MULTI JOG control or press the ENTER key 8.

NOTE

This operation cannot be undone. If you are going to erase a track or tracks, make sure that they are recordings that you really want to erase!

6If the erase operation has been selected, the word ERASE flashes on the display, and the timer starts counting down from 0:20 (20 seconds).

7At the end of the countdown period, the word Complete appears briefly on the display, and the display returns to the track/time display.

5.2.2Erasing a whole disc

When you want to erase a whole disc (all the tracks on a disc), follow the procedure below:

1With the disc loaded, and the unit in stop mode, press the ERASE key (G or D).

2Turn the MULTI JOG control B or use the SKIP keys I until the display shows ERASE DISC?.

3If you do not want to proceed with the erase operation, press any other key (such as the STOP key).

4To erase the contents of the disc, press the MULTI JOG control or press the ENTER key 8.

5 • After recording—Erasing

NOTE

This operation cannot be undone. If you are going to erase a disc, make sure that it contains only record- ings that you really want to erase!

5If the erase operation has been selected, the word ERASE flashes on the display, and the timer starts counting down a time value shown on the display.

6At the end of the countdown period, the word Complete appears briefly on the display, and the display returns to the track/time display.

5.2.3Refreshing a disc

If a CD-RW disc has been corrupted at any point (e.g. power has been cut off in the middle of a final- ize operation, etc.), or has been used in a computer or another piece of equipment that makes it unreadable, it is possible to “refresh” the disc to make it usable again. This is equivalent to formatting a disk on a computer to prepare it for use. This operation destroys all data on the disc.

1With the disc loaded, and the unit in stop mode, press the ERASE key (G or D).

2Turn the MULTI JOG control B or use the SKIP keys I until the display shows DISC REFRESH.

3If you do not want to proceed with the refresh operation, press any other key (such as the STOP key).

4To refresh the disc, press the MULTI JOG con- trol or press the ENTER key 8.

NOTE

This operation cannot be undone. If you are going to refresh a disc, make sure that it contains only record- ings that you really want to erase!

5If the erase operation has been selected, the word ERASE flashes on the display, and the timer starts counting down. The refresh opera- tion typically takes around 20 minutes or so.

6At the end of the countdown period, the word Complete appears briefly on the display, and the display returns to the track/time display (of course, there are no tracks, and the disc is as the start, with the total time of the disc available for recording).

TASCAM CD-RW700 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents CD-RW700 Do not cut off the mains plug from this equipment Important Safety PrecautionsImportant Safety Instructions Pour le Canada For CanadaTable of Contents About CD-R and CD-RW discs IntroductionEnvironmental considerations Introduction-FinalizingFinalizing Unpacking the CD-RW700Handling of compact discs Introduction-Environmental considerationsBeware of condensation Never use a stabilizer or printable discsDefault settings Dimensional drawingRecommended media Features of the CD-RW700 Front panel Features of the CD-RW700-Front panelFeatures of the CD-RW700-Rear panel Remote control unitRear panel Features of the CD-RW700-Connections Timer operationsConnections Features of the CD-RW700-Timer operations Setting the timerUsing the timer Track search Playback operationsSimple playback operations Time display modesPlayback operations-Programmed order playback Programmed order playbackRepeat play Input monitoring Signal volumeRecording Input selectionTime display while recording Recording-Basic recordingBasic recording Playing back tracksAdvanced recording Recording-Advanced recording66, and -72dB Automatic track division Automatic track increment Digital directFade-in and fade-out Recording-RehearsalRehearsal Rec mute functionPress the Rhsl key 4 so that the display shows Waiting Sync Rehearsal for synchronized recordingRehearsal for track division Erasing tracks After recordingErasing 1 Unfinalizing CD-RW discsAfter recording-Erasing Erasing a whole discRefreshing a disc Reference and specifications TroubleshootingSpecifications

CD-RW700 specifications

The Tascam CD-RW700 is a professional-grade audio CD recorder designed for serious musicians, sound engineers, and audio enthusiasts. With a robust build quality and a multitude of features, this unit is well-suited for both studio and live settings.

One of the standout features of the CD-RW700 is its ability to record, erase, and re-record on CD-R and CD-RW media. This flexibility allows users to create high-quality CDs for various applications, from music albums to archival projects. The CD-RW700 employs a sophisticated digital-to-analog converter, ensuring pristine sound quality during playback and recording.

The unit supports a variety of recording formats, including CD-DA, WAV, and MP3, catering to different audio needs. The high-speed dubbing function allows for rapid copying of CDs, making it ideal for situations where time is of the essence. Additionally, the device features a high-quality pitch control and signal processing function, enabling users to adjust the pitch and tempo of recordings with ease.

Equipped with a clear LCD display, the CD-RW700 provides users with real-time feedback on recording levels, time elapsed, and remaining time. This user-friendly interface enhances the overall experience, allowing for straightforward navigation and operation. The built-in metronome and tuner serve as useful tools for musicians during recording sessions.

Connectivity is another strong point of the CD-RW700. It features balanced XLR inputs and outputs, as well as unbalanced RCA connections, ensuring compatibility with a wide range of audio equipment. The inclusion of a coaxial digital input and output further enhances its versatility, allowing for high-quality digital transfers.

The CD-RW700 also supports various anti-shock technologies, ensuring smooth playback without interruptions during live performances or sensitive recordings. This reliability makes it an excellent choice for both professional studios and home setups.

In conclusion, the Tascam CD-RW700 combines advanced recording technologies with comprehensive features, making it an essential tool for anyone looking to produce high-quality audio CDs. Its robust design, user-friendly interface, and versatile connectivity options position it as a leading choice in the realm of CD recording equipment. Whether you’re a musician, producer, or sound technician, the Tascam CD-RW700 offers the reliability and performance needed to meet demanding audio requirements.
Top Page Image Contents