Poulan 96192003400 Maintenance, General Recommendations, Before Each Use, Lubrication, Tires

Page 13
MAINTENANCE

MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower.

At least once a season, check to see if you should make any of the adjustments described in the Service and Ad- justments section of this manual.

•At least once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRICATION CHART”).

➀SAE 30 Motor Oil

➁ See “ENGINE” in

Maintenance section

➂ General

Purpose

Grease

➀ Pivot points

➁ Engine

➂ Auger

oil

grease fittings

SNOW THROWER

Always observe the safety rules when performing any maintenance.

TIRES

•Maintain proper air pressure in both tires (14–17 PSI).

•Keep tires free of gasoline and oil, which can harm rubber.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT827ESPreparation TrainingOperation PRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and HOW TO SET UP YOUR SNOW THROWERTOOL BOX See Fig. UNFOLD UPPER HANDLECHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS STOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig. TO CONTROL SNOW DISCHARGE See Figs. 10 &TO ADJUST SKID PLATES See Fig. USING THE CLEAN-OUTTOOL See Fig.TO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See Fig.SCRAPER BAR See Fig. BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL See Fig. ADD GASOLINE See Fig.BEFORE STOPPING SNOW THROWING TIPSIF RECOIL STARTER HAS FROZEN GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGBELTS AUGER GEAR CASE2.Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig. TO REMOVE WHEELS See Fig. TO ADJUST CABLE TENSION See Fig.CARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTION PARTPART AUGER HOUSING / IMPELLER ASSEMBLYDESCRIPTION PARTPART CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE PART DRIVEDESCRIPTION PARTPART 2 3 1 CHASSIS / ENGINE / PULLEYS423185X505 ENGINE MOUNTING PLATEPART WHEEL ASSEMBLY LH WHEELS187833X428 187865X428SAFETY IGNITION KEY BAG OF PARTS01.14.007-A 1930711 4 1 DECALS181037 DECAL, DANGERSERVICE NOTES SERVICE NOTES LIMITED WARRANTY
Top Page Image Contents