Poulan XT827ES How To Set Up Your Snow Thrower, Assembly / Pre-Operation, TOOL BOX See Fig

Page 5
HOW TO SET UP YOUR SNOW THROWER

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD

 

 

RETAINER

 

 

SPRING

SPEED

 

SPEED

CONTROL

CONTROL

BRACKET

 

LEVER

FIG. 2

5

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE

RETAINER

CONTROL LEVER

SPRING

 

TRACTION

 

DRIVE

 

CONTROL

 

ROD

DRIVE

 

CONTROL

 

BRACKET

 

FIG. 4

Image 5
Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT827ESOperation TrainingPreparation PRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and HOW TO SET UP YOUR SNOW THROWERTOOL BOX See Fig. UNFOLD UPPER HANDLECHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS STOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig. TO CONTROL SNOW DISCHARGE See Figs. 10 &TO ADJUST SKID PLATES See Fig. USING THE CLEAN-OUTTOOL See Fig.TO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See Fig.SCRAPER BAR See Fig. BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL See Fig. ADD GASOLINE See Fig.IF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGBELTS AUGER GEAR CASE2.Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig. TO REMOVE WHEELS See Fig. TO ADJUST CABLE TENSION See Fig.CARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTION PARTPART AUGER HOUSING / IMPELLER ASSEMBLYDESCRIPTION PARTPART CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE PART DRIVEDESCRIPTION PARTDESCRIPTION 2 3 1 CHASSIS / ENGINE / PULLEYS423185X505 ENGINE MOUNTING PLATEPART WHEEL ASSEMBLY LH WHEELS187833X428 187865X428SAFETY IGNITION KEY BAG OF PARTS01.14.007-A 1930711 4 1 DECALS181037 DECAL, DANGERSERVICE NOTES SERVICE NOTES LIMITED WARRANTY