Poulan XT827ES, 428863, 96192003400 owner manual Operation, Meets A.N.S.I. Safety Requirements

Page 8

MEETS A.N.S.I. SAFETY REQUIREMENTS

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

IGNITION

KEYON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

	ELECTRIC	AUGER	DISCHARGE CHUTE CONTROL LEVER
	START BUTTON	AUGER	DISCHARGE CHUTE CONTROL LEVER
	START BUTTON	CONTROL
		CONTROL
	RECOIL LEVER		DRIVE SPEED	TRACTION
	(AUXILIARY)		CONTROL LEVER	DRIVE
	STARTER			CONTROL
	HANDLE			LEVER
		CHUTE
	DEFLECTOR
				LIGHT
				DEFLECTOR
				CHUTE KNOB
	DISCHARGE
	CHUTE

	CLEAN-OUT TOOL	HANDLE
	CLEAN-OUT TOOL	KNOB
		KNOB
		MUFFLER
		TOOLBOX

SKID PLATE

FIG. 8

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

8

Image 8

Contents OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT827ESOperation TrainingPreparation TABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON HOW TO SET UP YOUR SNOW THROWER INSTALL SPEED CONTROL ROD See Figs. 1 andTOOL BOX See Fig. UNFOLD UPPER HANDLEINSTALL AUGER CONTROL ROD See Figs. 5 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig. TO CONTROL SNOW DISCHARGE See Figs. 10 &USING THE CLEAN-OUTTOOL See Fig. TO ADJUST SKID PLATES See Fig.TO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See Fig.BEFORE STARTING THE ENGINE SCRAPER BAR See Fig.CHECK ENGINE OIL LEVEL See Fig. ADD GASOLINE See Fig.IF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING MAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATIONCLEANING ENGINEBELTS AUGER GEAR CASESERVICE AND ADJUSTMENTS 2.Remove safety ignition keyTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig. TO ADJUST CABLE TENSION See Fig. TO REMOVE WHEELS See Fig.CARBURETOR ENGINE SPEEDSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING Loss of powerDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY PART DESCRIPTIONAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE DRIVE PARTDESCRIPTION PARTDESCRIPTION CHASSIS / ENGINE / PULLEYS 2 3 1423185X505 ENGINE MOUNTING PLATECHASSIS / ENGINE / PULLEYS WHEELS WHEEL ASSEMBLY LH187833X428 187865X428BAG OF PARTS SAFETY IGNITION KEY01.14.007-A 193071DECALS 1 4 1181037 DECAL, DANGERSERVICE NOTES SERVICE NOTES LIMITED WARRANTY