Poulan XT827ES, 428863 Service And Adjustments, Engine, TO REMOVE WHEELS See Fig, Carburetor

Page 17
TO REMOVE WHEELS (See Fig. 20)

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 20)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 20

TO ADJUST CABLE TENSION (See Fig. 21)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 21

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT827ESOperation TrainingPreparation PRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and HOW TO SET UP YOUR SNOW THROWERTOOL BOX See Fig. UNFOLD UPPER HANDLECHECK TIRE PRESSURE INSTALL AUGER CONTROL ROD See Figs. 5 andKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS STOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig. TO CONTROL SNOW DISCHARGE See Figs. 10 &TO ADJUST SKID PLATES See Fig. USING THE CLEAN-OUTTOOL See Fig.TO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See Fig.SCRAPER BAR See Fig. BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL See Fig. ADD GASOLINE See Fig.IF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING GENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGBELTS AUGER GEAR CASE2.Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig. TO REMOVE WHEELS See Fig. TO ADJUST CABLE TENSION See Fig.CARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTION PARTPART AUGER HOUSING / IMPELLER ASSEMBLYDESCRIPTION PARTPART CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE PART DRIVEDESCRIPTION PARTDESCRIPTION 2 3 1 CHASSIS / ENGINE / PULLEYS423185X505 ENGINE MOUNTING PLATEPART WHEEL ASSEMBLY LH WHEELS187833X428 187865X428SAFETY IGNITION KEY BAG OF PARTS01.14.007-A 1930711 4 1 DECALS181037 DECAL, DANGERSERVICE NOTES SERVICE NOTES LIMITED WARRANTY
Top Page Image Contents