Poulan 428863, 96192003400 Assembly / Pre-Operation, INSTALL AUGER CONTROL ROD See Figs. 5 and

Page 6
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

AUGER CONTROL ROD

AUGER

RETAINER

CONTROL

LEVER

SPRING

 

 

AUGER

CONTROL

BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE

 

 

ROTATER

 

3/8 LOCKNUT

HEAD

 

 

 

 

3/8 WASHER

 

 

PIN

 

 

THREADED

 

 

STUD

 

ALIGN BEFORE

ROTATER HEAD

CHUTE

MOUNTING

BRACKET

TIGHTENING LOCKNUT

BRACKET

FIG. 7

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents IMPORTANT MANUAL OWNERS MANUAL MODEL NUMBERSNOW THROWER XT827ESTraining PreparationOperation Maintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION PARTS PACKED SEPARATELY IN CARTONREMOVE SNOW THROWER FROM CARTON TOOL BOX See Fig. HOW TO SET UP YOUR SNOW THROWERINSTALL SPEED CONTROL ROD See Figs. 1 and UNFOLD UPPER HANDLEINSTALL AUGER CONTROL ROD See Figs. 5 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS TO USE CHOKE CONTROL See Fig. HOW TO USE YOUR SNOW THROWERSTOPPING TO CONTROL SNOW DISCHARGE See Figs. 10 &TO THROW SNOW See Fig USING THE CLEAN-OUTTOOL See Fig.TO ADJUST SKID PLATES See Fig. TO MOVE FORWARD AND BACKWARD See Fig.CHECK ENGINE OIL LEVEL See Fig. BEFORE STARTING THE ENGINESCRAPER BAR See Fig. ADD GASOLINE See Fig.SNOW THROWING TIPS BEFORE STOPPINGIF RECOIL STARTER HAS FROZEN BEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONBELTS CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS2.Remove safety ignition key CHUTE DEFLECTORTO REPLACE BELTS See Fig. CARBURETOR TO ADJUST CABLE TENSION See Fig.TO REMOVE WHEELS See Fig. ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY PART DESCRIPTIONDESCRIPTION AUGER HOUSING / IMPELLER ASSEMBLYPART PARTDESCRIPTION CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE DESCRIPTION DRIVEPART PARTDRIVE 423185X505 CHASSIS / ENGINE / PULLEYS2 3 1 ENGINE MOUNTING PLATEDESCRIPTION 187833X428 WHEELSWHEEL ASSEMBLY LH 187865X42801.14.007-A BAG OF PARTSSAFETY IGNITION KEY 193071181037 DECALS1 4 1 DECAL, DANGERSERVICE NOTES SERVICE NOTES LIMITED WARRANTY
Top Page Image Contents