Poulan 96192003400, 428863, XT827ES Parts Packed Separately In Carton, Assembly / Pre-Operation

Page 4
PARTS PACKED SEPARATELY IN CARTON

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

(1) MULTI-

WRENCH

(180684)

(2) FLAT WASHERS

 

(1) POWER CORD

 

(1) DISCHARGE CHUTE

(198563)

(3) RETAINER

 

 

 

 

 

SPRINGS

 

 

(169675)

ROTATOR HEAD MOUNTING

(2) CARRIAGE BOLTS 3/8-16 x 2.25

SAFTEY IGNITION KEY (S) (193071)

(1) WASHER 3/8

(1) LOCKNUT 3/8

(19131316)

(73800600)

(2) HANDLE KNOBS

EXTASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTONRA SHEAR BOLTS AND NUTS

(2) SHEAR BOLTS 1/4-20 x 1-3/4

(2) LOCKNUTS

(192090)

1/4-20

 

(73800400)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

4

Image 4
Contents OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT827ESPreparation TrainingOperation TABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONREMOVE SNOW THROWER FROM CARTON HOW TO SET UP YOUR SNOW THROWER INSTALL SPEED CONTROL ROD See Figs. 1 andTOOL BOX See Fig. UNFOLD UPPER HANDLEINSTALL AUGER CONTROL ROD See Figs. 5 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig. TO CONTROL SNOW DISCHARGE See Figs. 10 &USING THE CLEAN-OUTTOOL See Fig. TO ADJUST SKID PLATES See Fig.TO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See Fig.BEFORE STARTING THE ENGINE SCRAPER BAR See Fig.CHECK ENGINE OIL LEVEL See Fig. ADD GASOLINE See Fig.BEFORE STOPPING SNOW THROWING TIPSIF RECOIL STARTER HAS FROZEN MAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATIONCLEANING ENGINEBELTS AUGER GEAR CASESERVICE AND ADJUSTMENTS 2.Remove safety ignition keyTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig. TO ADJUST CABLE TENSION See Fig. TO REMOVE WHEELS See Fig.CARBURETOR ENGINE SPEEDSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING Loss of powerDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY PART DESCRIPTIONAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE DRIVE PARTDESCRIPTION PARTPART CHASSIS / ENGINE / PULLEYS 2 3 1423185X505 ENGINE MOUNTING PLATECHASSIS / ENGINE / PULLEYS WHEELS WHEEL ASSEMBLY LH187833X428 187865X428BAG OF PARTS SAFETY IGNITION KEY01.14.007-A 193071DECALS 1 4 1181037 DECAL, DANGERSERVICE NOTES SERVICE NOTES LIMITED WARRANTY