MTD OGST-3106 manual To Engage Wheel Drive, To Engage Augers, Operating Tips

Page 11

loud clattering sound, which is not harmful to the engine or starter.

•Move throttle control to “stop” or “off” position.

•Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

NOTE: Keep key in a safe place. Engine will not start without ignition key.

•Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times.

To Engage Wheel Drive

•With the engine running near top speed, move shift lever to one of the eight positions to set desired speed and direction. Select speed appropriate for the snow conditions that exist.

NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower operation.

•Squeeze wheel drive control against the right handle to move the snow thrower; release it to stop.

IMPORTANT: NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel.

To Engage Augers

•To engage augers and start snow throwing, squeeze the auger control against the left handle.

•To disengage power to the augers, release both the auger control and the wheel drive control, if engaged.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150°F (65°C ). Avoid these areas.

•If possible, remove snow immediately after it falls.

•Discharge snow downwind whenever possible.

•Slightly overlap each previous path.

•Set the skid shoes 1/4" below the shave plate for normal usage. Adjust it upward for hard-packed snow and downward when using on gravel or crushed rock.

Chute Clean-Out Tool

The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Never use your hand to clean a clogged chute or chute opening; use this clean-out tool instead.

•Release both the wheel drive control and the auger drive control levers.

•Stop the engine by removing the ignition key.

•Remove the chute clean-out tool from the clip which secures it to the rear of the auger housing. See Figure 12.

•Use the shovel-shaped end of the clean-out tool to remove any snow and ice in the discharge chute.

•Re-fasten the clean-out tool to the mounting clip on the rear of the auger housing and restart engine.

•While standing in the operator’s position (behind the snow thrower), engage the auger clutch lever for a few seconds to clear any remaining snow or ice from the discharge chute before continuing to clear snow.

Chute Clean-Out Tool

Clip

Figure 12

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageLoose Parts Items Required For AssemblyBefore Assembly Assembling Handle Assembling Your Snow ThrowerAttaching Chute Crank Attaching the Chute AssemblyAuger Control Chute Clean-Out ToolFinal Adjustments Wheel Drive Control & Shift LeverDrive Control / Auger Control Lock Knowing Your Snow ThrowerTire Pressure Pneumatic Tires Discharge Chute Safety Ignition KeyChute Clean-Out Tool Shift LeverTo Start Engine Operating Your Snow ThrowerBefore Starting Gas & Oil Fill-UpOperating Tips To Engage Wheel DriveTo Engage Augers Wheel Drive Control Chute AssemblyShift Rod Auger ControlLubrication Maintaining Your Snow ThrowerSkid Shoe General RecommendationsWheel Drive Control / Auger Control Lock Friction Wheel RubberDrive Belts EngineAuger Belt Servicing Your Snow ThrowerAugers Replacing Belts Shave Plate and Skid ShoesDrive Belt Sprocket Hex Shaft Changing Friction Wheel RubberOFF-SEASON Storage TroubleshootingTractor Attachment Warranty Three 3 Year Limited Warranty103 Part RÉF Pièce Description Serrez à un couple de 20-30 po-lb Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Style Commerciale Utilisation Dépannage DE Guide 9 Chapitre Nongpi du Hex Moyeu Arbre NongPi UregFiLa de manivelle la et courroie-couvre le Remontez Frottement de roueCaoutchouc en bague la de Changement GoulotteCourroies les de Remplacement ’entraînement Courroies Patins et LameTarières MoteurLubrification Général d’ordre Recommandations’éjection Goulotte Tarière la de CommandePatin Goulotte la de et patins des tarière Roues des l’entraînement de CommandeLa de commande la de réglage tout pour réglages» Laissez Remarque ’utilisation ConseilsTarières les de Embrayage Trous trois à courant de prise une avez vous Si ’huile et d’essence PleinsDémarrage le Avant Vitesses de Levier Tous dans égale pas n’est pression la Si Remarque ’autre deQue plus côté d’un tirer de risque machine la pneus, les La à «Réglages» chapitre Le dans roues» des l’entraînement de «CommandeRéglages Derniers Goulotte la de dégagement de OutilExcessivement Goulotte la de manivelle la de MontageGoulotte la de Montage Souffleuse la de châssis le de l’arrière à Regardez Montage 2 ChapitreCisaillement de Boulons Responsabilité Votre Remisage ET Entretien Formation PréparationEgPa Contenu Egl’assembla Procéder de Avant’utilisation Notice

OGST-3106 specifications

The MTD OGST-3106 is an innovative and versatile outdoor gas-powered string trimmer designed to meet the demands of both professional landscapers and passionate gardeners. This robust machine combines power, efficiency, and ease of use, making it a top choice for managing grass, weeds, and other vegetation.

One of the standout features of the MTD OGST-3106 is its powerful 31cc 2-cycle engine. This engine is engineered to deliver exceptional performance, allowing users to tackle thick underbrush and heavy grass with ease. The engine is designed for optimal fuel efficiency, reducing the need for frequent refueling during larger jobs. In addition to power, the lightweight design of the trimmer ensures that users can maneuver it effortlessly, reducing fatigue even during prolonged use.

The MTD OGST-3106 incorporates a straight shaft design, which provides extended reach for accessing hard-to-reach areas such as under decks or along fences. This feature enhances its versatility, making it suitable for a variety of applications, from trimming along sidewalks to edging flower beds. Moreover, the unit is equipped with a dual-line cutting head that allows for increased cutting width and efficiency, ensuring a cleaner and faster job.

Another key characteristic of the MTD OGST-3106 is its easy-start technology. The trimmer features user-friendly starting mechanisms that make it simple to get the engine running, even for those who may not have extensive experience with gas-powered equipment. This eliminates some of the common hassles associated with starting similar machines, making it accessible to users of all skill levels.

Durability is a hallmark of the MTD OGST-3106, constructed with high-quality materials that withstand the rigors of outdoor use. Its robust build ensures longevity and reliability over time, even when facing tough environmental conditions. The trimmer also includes ergonomic grips that enhance comfort and control, enabling users to work efficiently while minimizing strain on their hands and wrists.

In conclusion, the MTD OGST-3106 is a powerful and user-friendly gas string trimmer that combines advanced technology with practical features. It is ideal for anyone looking to maintain their outdoor space effectively. Whether you are a professional landscaper or a DIY enthusiast, the MTD OGST-3106 is designed to help you achieve professional-quality results with ease and efficiency. Its blend of power, durability, and ergonomic design sets it apart in the competitive market of outdoor power equipment.
Top Page Image Contents