MTD OGST-3106 manual Shift Lever, Discharge Chute, Chute Tilt Control, Wheel Steering Controls

Page 9

Auger Control

The auger control is located on the left handle. Squeeze the auger control to engage the augers. Release to stop the snow throwing action. The drive control must also be released in order to stop auger.

Shift Lever

The shift lever is located in the center

6

of the handle panel and is used to

5

determine ground speed and

4

direction of travel. It can be moved

3

into any of eight positions.

2

IMPORTANT: Always release drive

F 1

control before changing speeds.

Forward: The snow thrower has six

forward (F) speeds. Position one (1)

R R1

 

is the slowest and position six (6) is

R2

the fastest.

 

Reverse: The snow thrower has two

 

reverse (R) speeds—R1 is the slower

 

of the two.

 

Discharge Chute

 

The angle of the discharge chute controls the distance that the snow is thrown. Tilt the discharge chute up for greater distance; tilt down for less distance.

Chute Tilt Control

The distance snow is thrown can be changed by adjusting the angle of the chute assembly. Move the chute tilt control forward to decrease the distance, toward the rear to increase.

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles.

•Squeeze the right control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you are familiar with these controls.

Skid Shoe

The skid shoe position is determined by the condition of the ground from where snow has to be removed. Higher the snow level, lower will be the skid shoe. Adjust it accordingly.

Headlight

The headlight is on whenever the engine is running.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine.

Chute Crank

The chute crank is located on the left side of the snow thrower. Use it to change the direction in which snow is thrown. Avoid targetting persons, animals or cars and buildings.

CLOCKWISE TO DISCHARGE LEFT

COUNTER CLOCKWISE TO DISCHARGE RIGHT

Safety Ignition Key

The safety ignition key must be fully inserted in the switch before the unit will start. Remove key when snow thrower is not in use. Do not attempt to turn the key.

Chute Clean-Out Tool

The chute clean-out tool is designed to clear a clogged discharge chute. Refer to page 11 for instructions on it.

WARNING: Never use your hand to clear a clogged discharge chute. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageBefore Assembly Assembling Handle Items Required For AssemblyAssembling Your Snow Thrower Loose PartsAttaching Chute Crank Attaching the Chute AssemblyFinal Adjustments Chute Clean-Out ToolWheel Drive Control & Shift Lever Auger ControlKnowing Your Snow Thrower Tire Pressure Pneumatic TiresDrive Control / Auger Control Lock Chute Clean-Out Tool Safety Ignition KeyShift Lever Discharge ChuteBefore Starting Operating Your Snow ThrowerGas & Oil Fill-Up To Start EngineTo Engage Wheel Drive To Engage AugersOperating Tips Shift Rod Chute AssemblyAuger Control Wheel Drive ControlSkid Shoe Maintaining Your Snow ThrowerGeneral Recommendations LubricationDrive Belts Friction Wheel RubberEngine Wheel Drive Control / Auger Control LockAugers Replacing Belts Servicing Your Snow ThrowerShave Plate and Skid Shoes Auger BeltDrive Belt Sprocket Hex Shaft Changing Friction Wheel RubberOFF-SEASON Storage TroubleshootingTractor Attachment Warranty Three 3 Year Limited Warranty103 Part RÉF Pièce Description Serrez à un couple de 20-30 po-lb Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Style Commerciale Utilisation Dépannage DE Guide 9 Chapitre Nongpi du Hex Moyeu Arbre NongPi UregFiCaoutchouc en bague la de Changement Frottement de roueGoulotte La de manivelle la et courroie-couvre le RemontezCourroies les de Remplacement Tarières Patins et LameMoteur ’entraînement CourroiesLubrification Général d’ordre RecommandationsTarière la de Commande Patin’éjection Goulotte Roues des l’entraînement de Commande La de commande la de réglage tout pour réglages»Goulotte la de et patins des tarière ’utilisation Conseils Tarières les de EmbrayageLaissez Remarque ’huile et d’essence Pleins Démarrage le AvantTrous trois à courant de prise une avez vous Si Vitesses de Levier ’autre de Que plus côté d’un tirer de risque machine la pneus, lesTous dans égale pas n’est pression la Si Remarque Réglages Derniers Le dans roues» des l’entraînement de «CommandeGoulotte la de dégagement de Outil La à «Réglages» chapitreGoulotte la de manivelle la de Montage Goulotte la de MontageExcessivement Montage 2 Chapitre Cisaillement de BoulonsSouffleuse la de châssis le de l’arrière à Regardez Responsabilité Votre Remisage ET Entretien Formation PréparationEgPa Contenu Egl’assembla Procéder de Avant’utilisation Notice

OGST-3106 specifications

The MTD OGST-3106 is an innovative and versatile outdoor gas-powered string trimmer designed to meet the demands of both professional landscapers and passionate gardeners. This robust machine combines power, efficiency, and ease of use, making it a top choice for managing grass, weeds, and other vegetation.

One of the standout features of the MTD OGST-3106 is its powerful 31cc 2-cycle engine. This engine is engineered to deliver exceptional performance, allowing users to tackle thick underbrush and heavy grass with ease. The engine is designed for optimal fuel efficiency, reducing the need for frequent refueling during larger jobs. In addition to power, the lightweight design of the trimmer ensures that users can maneuver it effortlessly, reducing fatigue even during prolonged use.

The MTD OGST-3106 incorporates a straight shaft design, which provides extended reach for accessing hard-to-reach areas such as under decks or along fences. This feature enhances its versatility, making it suitable for a variety of applications, from trimming along sidewalks to edging flower beds. Moreover, the unit is equipped with a dual-line cutting head that allows for increased cutting width and efficiency, ensuring a cleaner and faster job.

Another key characteristic of the MTD OGST-3106 is its easy-start technology. The trimmer features user-friendly starting mechanisms that make it simple to get the engine running, even for those who may not have extensive experience with gas-powered equipment. This eliminates some of the common hassles associated with starting similar machines, making it accessible to users of all skill levels.

Durability is a hallmark of the MTD OGST-3106, constructed with high-quality materials that withstand the rigors of outdoor use. Its robust build ensures longevity and reliability over time, even when facing tough environmental conditions. The trimmer also includes ergonomic grips that enhance comfort and control, enabling users to work efficiently while minimizing strain on their hands and wrists.

In conclusion, the MTD OGST-3106 is a powerful and user-friendly gas string trimmer that combines advanced technology with practical features. It is ideal for anyone looking to maintain their outdoor space effectively. Whether you are a professional landscaper or a DIY enthusiast, the MTD OGST-3106 is designed to help you achieve professional-quality results with ease and efficiency. Its blend of power, durability, and ergonomic design sets it apart in the competitive market of outdoor power equipment.
Top Page Image Contents