MTD OGST-3106 manual Chute Clean-Out Tool, Final Adjustments, Wheel Drive Control & Shift Lever

Page 7

Chute Clean-Out Tool

•The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Use the clean-out tool to clear snow and ice which may lodge in the discharge chute during operation. Refer to the Operation section for more detailed information regarding the chute clean-out tool.

Final Adjustments

Make these final adjustments before operating your snow thrower for the first time. Failure to follow these instructions may cause damage to the snow thrower.

Wheel Drive Control & Shift Lever

Perform the following test to determine need for adjustment:

•Move the shift lever into sixth (6) position. See Figure 11.

•With the drive control released, push the snow thrower forward, then pull it back. The machine should move freely.

•Engage the drive control and attempt to move the machine both forward and back, resistance should be felt.

•Move the shift lever into the fast reverse (R2) position and repeat the previous two steps.

If you experienced resistance rolling the unit, either when repositioning the shift lever from 6 to R2 or when attempting to move the machine with the drive control released, adjust the drive control immediately. To adjust, proceed as follows:

•Loosen the jam nut on the traction control cable and unthread the cable one full turn.

•Recheck adjustment.

•Retighten the jam nut to secure the cable when correct adjustment is reached.

NOTE: For more details, refer to Wheel Drive Control Adjustment in the Adjustment Section of this manual.

Auger Control

Check the adjustment of the auger control as follows:

•When the auger control is released and in the disengaged “up” position, the cable should have very little slack, but should NOT be tight. See Figure 8.

Released/Disengaged

Position

Figure 8

WARNING: Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compromise the safety of the snow thrower.

•In a well-ventilated area, start the snow thrower engine as instructed on page 10. Make sure the throttle is set in the fast position.

•While standing in the operator’s position (behind the snow thrower) engage the auger.

•Allow the auger to remain engaged for approximately ten seconds before releasing the auger control. Repeat this several times.

•With the engine running in the fast position and the auger control lever in the disengaged “up” position, walk to the front of the machine.

•Confirm that the auger has completely stopped rotating and shows no signs of motion.

IMPORTANT: If the auger shows any signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for all moving parts to stop before readjusting the auger control cable.

•To readjust the control cable, unhook the spring (found on the end of the auger cable) from the auger actuator bracket. See Figure 9.

•Push the cable coupler through the end of the spring to expose the lock nut. See Figure 10.

•Thread the lock nut outward (down the coupler) three full turns to provide more slack in the cable and reattach the spring to the bracket.

•Repeat auger control test to verify for proper adjustment. Repeat previous steps to adjust more, if necessary.

Drive

Spring

Drive

ActuatorBracket

Auger Auger

Spring Actuator Bracket

Figure 9

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageLoose Parts Items Required For AssemblyBefore Assembly Assembling Handle Assembling Your Snow ThrowerAttaching Chute Crank Attaching the Chute AssemblyAuger Control Chute Clean-Out ToolFinal Adjustments Wheel Drive Control & Shift LeverTire Pressure Pneumatic Tires Knowing Your Snow ThrowerDrive Control / Auger Control Lock Discharge Chute Safety Ignition KeyChute Clean-Out Tool Shift LeverTo Start Engine Operating Your Snow ThrowerBefore Starting Gas & Oil Fill-UpTo Engage Augers To Engage Wheel DriveOperating Tips Wheel Drive Control Chute AssemblyShift Rod Auger ControlLubrication Maintaining Your Snow ThrowerSkid Shoe General RecommendationsWheel Drive Control / Auger Control Lock Friction Wheel RubberDrive Belts EngineAuger Belt Servicing Your Snow ThrowerAugers Replacing Belts Shave Plate and Skid ShoesDrive Belt Sprocket Hex Shaft Changing Friction Wheel RubberOFF-SEASON Storage TroubleshootingTractor Attachment Warranty Three 3 Year Limited Warranty103 Part RÉF Pièce Description Serrez à un couple de 20-30 po-lb Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Style Commerciale Utilisation Dépannage DE Guide 9 Chapitre Nongpi du Hex Moyeu Arbre NongPi UregFiLa de manivelle la et courroie-couvre le Remontez Frottement de roueCaoutchouc en bague la de Changement GoulotteCourroies les de Remplacement ’entraînement Courroies Patins et LameTarières MoteurLubrification Général d’ordre RecommandationsPatin Tarière la de Commande’éjection Goulotte La de commande la de réglage tout pour réglages» Roues des l’entraînement de CommandeGoulotte la de et patins des tarière Tarières les de Embrayage ’utilisation ConseilsLaissez Remarque Démarrage le Avant ’huile et d’essence PleinsTrous trois à courant de prise une avez vous Si Vitesses de Levier Que plus côté d’un tirer de risque machine la pneus, les ’autre deTous dans égale pas n’est pression la Si Remarque La à «Réglages» chapitre Le dans roues» des l’entraînement de «CommandeRéglages Derniers Goulotte la de dégagement de OutilGoulotte la de Montage Goulotte la de manivelle la de MontageExcessivement Cisaillement de Boulons Montage 2 ChapitreSouffleuse la de châssis le de l’arrière à Regardez Responsabilité Votre Remisage ET Entretien Formation PréparationEgPa Contenu Egl’assembla Procéder de Avant’utilisation Notice

OGST-3106 specifications

The MTD OGST-3106 is an innovative and versatile outdoor gas-powered string trimmer designed to meet the demands of both professional landscapers and passionate gardeners. This robust machine combines power, efficiency, and ease of use, making it a top choice for managing grass, weeds, and other vegetation.

One of the standout features of the MTD OGST-3106 is its powerful 31cc 2-cycle engine. This engine is engineered to deliver exceptional performance, allowing users to tackle thick underbrush and heavy grass with ease. The engine is designed for optimal fuel efficiency, reducing the need for frequent refueling during larger jobs. In addition to power, the lightweight design of the trimmer ensures that users can maneuver it effortlessly, reducing fatigue even during prolonged use.

The MTD OGST-3106 incorporates a straight shaft design, which provides extended reach for accessing hard-to-reach areas such as under decks or along fences. This feature enhances its versatility, making it suitable for a variety of applications, from trimming along sidewalks to edging flower beds. Moreover, the unit is equipped with a dual-line cutting head that allows for increased cutting width and efficiency, ensuring a cleaner and faster job.

Another key characteristic of the MTD OGST-3106 is its easy-start technology. The trimmer features user-friendly starting mechanisms that make it simple to get the engine running, even for those who may not have extensive experience with gas-powered equipment. This eliminates some of the common hassles associated with starting similar machines, making it accessible to users of all skill levels.

Durability is a hallmark of the MTD OGST-3106, constructed with high-quality materials that withstand the rigors of outdoor use. Its robust build ensures longevity and reliability over time, even when facing tough environmental conditions. The trimmer also includes ergonomic grips that enhance comfort and control, enabling users to work efficiently while minimizing strain on their hands and wrists.

In conclusion, the MTD OGST-3106 is a powerful and user-friendly gas string trimmer that combines advanced technology with practical features. It is ideal for anyone looking to maintain their outdoor space effectively. Whether you are a professional landscaper or a DIY enthusiast, the MTD OGST-3106 is designed to help you achieve professional-quality results with ease and efficiency. Its blend of power, durability, and ergonomic design sets it apart in the competitive market of outdoor power equipment.
Top Page Image Contents