MTD OGST-3106 manual Attaching the Chute Assembly, Attaching Chute Crank

Page 6

Attaching the Chute Assembly

NOTE: Your chute assembly may or may not be assembled. If it requires assembly use the following instructions.

Chute Assembly

Hex Screw

Hex Lock Nut

Chute Flange

Keeper

Figure 3

•Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit. Place chute flange keepers beneath lip of chute assembly, with the flat side of chute flange keeper facing downward.

•Insert hex cap screws up through chute flange keeper and chute assembly as shown in Figure 3. Secure with hex flange locknuts. Tighten with two 7/16” wrenches. Do not over tighten.

Attaching Chute Crank

•Remove the hairpin clip from the upper chute crank and slide the upper chute crank through the upper chute crank bracket and into the lower chute crank. A pair of pliers may help in this job.

Upper Chute Crank

Upper Chute

Crank Bracket

Hairpin Clip

Lower Chute Crank

Figure 4

•Align the two holes on both chute cranks and secure with the hairpin clip removed earlier. See Figure 4.

•With the hex nuts loosened on the lower chute crank bracket (see Figure 5) adjust the bracket so that the spiral on the chute crank fully engages the teeth on the chute assembly. Tighten the nuts on the lower chute crank bracket securely.

Chute Directional

Control

Chute

Assembly

Lower Chute

Bracklet

Lock Nuts

Figure 5

•The cable ties normally are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Trim excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide located on top of the engine.

See Figure 6.

Cables Cable

Guide

Discharge

Chute

Figure 6

•Wrap the wire from the head lamp down the right handle until the wire can be plugged into the alternator lead wire under the fuel tank.

Alternator Lead

Alternator

Lead

Lamp Wire

NOTE: Wheels are omitted from illustration for clarity.

Figure 7

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilityAssembling Your Snow Thrower Items Required For AssemblyBefore Assembly Assembling Handle Loose PartsAttaching the Chute Assembly Attaching Chute CrankWheel Drive Control & Shift Lever Chute Clean-Out ToolFinal Adjustments Auger ControlKnowing Your Snow Thrower Tire Pressure Pneumatic TiresDrive Control / Auger Control Lock Shift Lever Safety Ignition KeyChute Clean-Out Tool Discharge ChuteGas & Oil Fill-Up Operating Your Snow ThrowerBefore Starting To Start EngineTo Engage Wheel Drive To Engage AugersOperating Tips Auger Control Chute AssemblyShift Rod Wheel Drive ControlGeneral Recommendations Maintaining Your Snow ThrowerSkid Shoe LubricationEngine Friction Wheel RubberDrive Belts Wheel Drive Control / Auger Control LockShave Plate and Skid Shoes Servicing Your Snow ThrowerAugers Replacing Belts Auger BeltDrive Belt Changing Friction Wheel Rubber Sprocket Hex ShaftTroubleshooting OFF-SEASON StorageThree 3 Year Limited Warranty Tractor Attachment Warranty103 Part RÉF Pièce Description Serrez à un couple de 20-30 po-lb Part RÉF Pièce Description RÉF Pièce Description 20 19 3468 58A 58B Part RÉF Pièce Description 995 x 12,0 Lg po Couple de 325-550 po-lb Style Style Commerciale Utilisation Dépannage DE Guide 9 Chapitre UregFi Nongpi du Hex Moyeu Arbre NongPiGoulotte Frottement de roueCaoutchouc en bague la de Changement La de manivelle la et courroie-couvre le RemontezCourroies les de Remplacement Moteur Patins et LameTarières ’entraînement CourroiesGénéral d’ordre Recommandations LubrificationTarière la de Commande Patin’éjection Goulotte Roues des l’entraînement de Commande La de commande la de réglage tout pour réglages»Goulotte la de et patins des tarière ’utilisation Conseils Tarières les de EmbrayageLaissez Remarque ’huile et d’essence Pleins Démarrage le AvantTrous trois à courant de prise une avez vous Si Vitesses de Levier ’autre de Que plus côté d’un tirer de risque machine la pneus, lesTous dans égale pas n’est pression la Si Remarque Goulotte la de dégagement de Outil Le dans roues» des l’entraînement de «CommandeRéglages Derniers La à «Réglages» chapitreGoulotte la de manivelle la de Montage Goulotte la de MontageExcessivement Montage 2 Chapitre Cisaillement de BoulonsSouffleuse la de châssis le de l’arrière à Regardez Responsabilité Votre Remisage ET Entretien Préparation FormationEgl’assembla Procéder de Avant EgPa Contenu’utilisation Notice

OGST-3106 specifications

The MTD OGST-3106 is an innovative and versatile outdoor gas-powered string trimmer designed to meet the demands of both professional landscapers and passionate gardeners. This robust machine combines power, efficiency, and ease of use, making it a top choice for managing grass, weeds, and other vegetation.

One of the standout features of the MTD OGST-3106 is its powerful 31cc 2-cycle engine. This engine is engineered to deliver exceptional performance, allowing users to tackle thick underbrush and heavy grass with ease. The engine is designed for optimal fuel efficiency, reducing the need for frequent refueling during larger jobs. In addition to power, the lightweight design of the trimmer ensures that users can maneuver it effortlessly, reducing fatigue even during prolonged use.

The MTD OGST-3106 incorporates a straight shaft design, which provides extended reach for accessing hard-to-reach areas such as under decks or along fences. This feature enhances its versatility, making it suitable for a variety of applications, from trimming along sidewalks to edging flower beds. Moreover, the unit is equipped with a dual-line cutting head that allows for increased cutting width and efficiency, ensuring a cleaner and faster job.

Another key characteristic of the MTD OGST-3106 is its easy-start technology. The trimmer features user-friendly starting mechanisms that make it simple to get the engine running, even for those who may not have extensive experience with gas-powered equipment. This eliminates some of the common hassles associated with starting similar machines, making it accessible to users of all skill levels.

Durability is a hallmark of the MTD OGST-3106, constructed with high-quality materials that withstand the rigors of outdoor use. Its robust build ensures longevity and reliability over time, even when facing tough environmental conditions. The trimmer also includes ergonomic grips that enhance comfort and control, enabling users to work efficiently while minimizing strain on their hands and wrists.

In conclusion, the MTD OGST-3106 is a powerful and user-friendly gas string trimmer that combines advanced technology with practical features. It is ideal for anyone looking to maintain their outdoor space effectively. Whether you are a professional landscaper or a DIY enthusiast, the MTD OGST-3106 is designed to help you achieve professional-quality results with ease and efficiency. Its blend of power, durability, and ergonomic design sets it apart in the competitive market of outdoor power equipment.
Top Page Image Contents