MTD 33, 45, 28 warranty Operating Tips, General Recommendations

Page 13

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150° F (65° C). Avoid these areas.

1.If possible, remove snow immediately after it falls.

2.Discharge snow downwind whenever possible.

3.Slightly overlap each previous path.

4.Set the skid shoes 1/4” below the shave plate for normal usage. Adjust them upward for hard-packed snow and downward when using on gravel or crushed rock.

General Recommendations

1.Always observe safety rules when performing any maintenance.

2.The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the snow thrower as instructed here.

3.Some adjustments will have to be made periodically to maintain your unit properly.

4.Periodically check all fasteners and make sure these are tight.

4

Operating

Your Snow

Thrower

WARNING

The muffler, engine and surrounding areas become hot and can cause a burn 150°F (65°C). Do not touch.

NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower operation.

IMPORTANT

NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 769-04100 28, 30, 33 & 45Two-Stage Snow Throwers06/10/08 Finding and Recording Model Number Table of ContentsCustomer Support There are rotating blades inside Safety SymbolsDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeItems Required For Assembly Setting Up Your Snow ThrowerLoose Parts Assembling HandleAttaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Lamp WiringFinal Adjustments Drift Cutters If EquippedSkid Shoes Check the adjustment of the auger control as followsTire Pressure Pneumatic Tires AugerKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpTo Engage Drive To Engage AugersOperating Tips Always observe safety rules when performing any maintenanceGeneral Recommendations If possible, remove snow immediately after it fallsMaking AdjustmentsShift Rod Drive ControlChute Bracket Adjustment Chute AssemblySee Figure Adjust skid shoes as follows Auger ControlLubrication Maintaining Your Snow ThrowerReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltChanging Friction Wheel Rubber Using a 3/4 wrench, hold the hex shaftSecure with the cupped washer and hex bolt removed earlier Friction WheelOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description Style Page Part RÉF Pièce Description Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Garantie cette de GarantiePas couvre ne limitée garantie Cette Com.mtdcanadaDépannage Solution Causes ProblèmeUse PropreAccompagne qui moteur du d’utilisation notice la dans Jours, 30 de plus pendant entreposé être doit moteur le SiFrottement de Roue Entretien’essieu de Poulie la De Fente Et commandes lesMoteur du Tout empêcher pour’enlevez ÉloignezTarière la de d’entraînement Courroie Boulon l’autre retirezRoues LubrificationVitesse de ment ’engrenageRéglages Vitesses de levier du Tige Des l’entraînement de Commande’essieu Support de’utilisation Conseils Général d’ordre RecommandationsNormale PendantREMARQUEtourner moteur le LaissezFaites Ne ’huile et d’essence PleinsGoulotte la de dégagement de Outil Goulotte la de Commande Roues des d’orientation CommandeGoulotte la de direction Fonctions 2 àSouffleuse la de Commandes Tiques Tarière la de CommandePneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilGoulotte la de Installation Vitesses de levier du tige la de Installation«Réglages» Bien passe qu’il ce jusqu’à raccord le sur TapezGuidon du Montage Goulotte la de manivelle la de Montage’assemblage pour requis Articles Cisaillement de BoulonsResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationVotre ’essence de ManipulationMachine la d’utiliser Sécurité de SymbolesVente-après service au d’abord adresser vous sans Vente-après ServiceModèle de numéro le trouver Pour Matières des Table06/10/08 04100-769 ’UTILISATION Notice

45, 33, 28 specifications

MTD (Machine Tool Division) has become synonymous with advanced machining solutions, particularly with its 28, 33, and 45 series, each designed for specific industrial applications yet sharing common core features that enhance performance and productivity.

The MTD 28 series is primarily focused on precision machining for small to medium components. One of its standout features is the high-speed spindle technology, which supports a range of drilling and milling operations with minimal downtime. The machine is equipped with a robust structure designed to absorb vibrations, ensuring high precision and surface finish quality. Additionally, the MTD 28 integrates an intuitive user interface, allowing operators to navigate complex machining processes with ease. The series supports multiple tool configurations, enabling rapid changeovers and versatility in production.

Moving to the MTD 33 series, this model is engineered for medium to large production runs. A key characteristic of the MTD 33 is its advanced automation capabilities, including automatic tool changers and integrated robotic systems. These technologies streamline operations, reducing cycle times significantly. The series also boasts enhanced thermal stability, which is crucial for maintaining accuracy in high-speed machining environments. Furthermore, the MTD 33 utilizes an adaptive control system that adjusts machine parameters in real-time, optimizing performance based on workload and material type.

The MTD 45 series is the flagship among them, designed for high-performance machining tasks in heavy industry. It features an expansive workspace and a powerful drive system that allows for the machining of large components with exceptional torque. This series utilizes advanced CNC controls, ensuring precision that meets industry standards. The MTD 45 is also equipped with advanced coolant and lubrication systems, enhancing tool life and ensuring optimal cutting conditions. Moreover, this model supports a variety of machining processes, including turning, milling, and grinding, further solidifying its versatility in diverse manufacturing settings.

In summary, the MTD 28, 33, and 45 series exemplify innovative engineering and user-centric design. With features like high-speed spindles, automation capabilities, and robust construction, these machines cater to varying production needs while ensuring precision and efficiency. Whether for small component fabrication or large scale industrial applications, MTD’s commitment to technological advancement enables businesses to achieve greater productivity and quality in their machining processes.
Top Page Image Contents