MTD 45, 33, 28 warranty Auger Control, Chute Assembly, Chute Bracket Adjustment, Retighten the nuts

Page 15

Skid Shoes

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position.

See Figure 5-4.

Adjust skid shoes as follows:

1.Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

2.Raise or lower the skid shoe to desired position.

3.Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear.

4. Repeat on the other side of the snow thrower.

Auger Control

Refer to instructions on page 9 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to page 9 for instructions.

The remote chute control cables have been pre-adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so:

1.Loosen the two nuts which secure the chute bracket and reposition it slightly. See Figure 5-5.

2.Retighten the nuts.

Figure 5-4

Figure 5-5

5

Making

Adjustments

IMPORTANT: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 28, 30, 33 & 45Two-Stage Snow Throwers 769-0410006/10/08 Table of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineAssembling Handle Setting Up Your Snow ThrowerItems Required For Assembly Loose PartsAttaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Lamp WiringClean-Out Tool Final AdjustmentsAuger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 To Engage Augers Gas & Oil Fill-UpStopping The Engine To Engage DriveIf possible, remove snow immediately after it falls Always observe safety rules when performing any maintenanceOperating Tips General RecommendationsDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsMaintaining Your Snow Thrower LubricationReplacing Belts Remove Loosen Auger BeltPulley Slot Drive BeltFriction Wheel Using a 3/4 wrench, hold the hex shaftChanging Friction Wheel Rubber Secure with the cupped washer and hex bolt removed earlierOff-Season Storage Problem Cause Remedy Trouble Shooting05.28.08 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 21 ft./lbs. maximum 305-342 cc618-04514 Worm Gear Box Ass’y w/ grease fitting Part RÉF Pièce Description Style Page Part RÉF Pièce Description Part RÉF Pièce Description For parts and/or accessories refer to customer support on Page Com.mtdcanada GarantieGarantie cette de Pas couvre ne limitée garantie CetteDépannage Solution Causes ProblèmeJours, 30 de plus pendant entreposé être doit moteur le Si PropreUse Accompagne qui moteur du d’utilisation notice la dansEntretien Frottement de Roue’essieu de Tout empêcher pour Et commandes lesPoulie la De Fente Moteur duBoulon l’autre retirez Éloignez’enlevez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentRéglages Support de Des l’entraînement de CommandeVitesses de levier du Tige ’essieuPendantREMARQUEtourner moteur le Laissez Général d’ordre Recommandations’utilisation Conseils Normale’huile et d’essence Pleins Faites NeGoulotte la de dégagement de Outil Fonctions 2 à Roues des d’orientation CommandeGoulotte la de Commande Goulotte la de directionSouffleuse la de Commandes Tarière la de Commande TiquesPneuma Bandages pneus des Pression Pas Goulotte la de dégagement de OutilBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation «Réglages»Cisaillement de Boulons Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de SymbolesMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour06/10/08 04100-769 ’UTILISATION Notice

45, 33, 28 specifications

MTD (Machine Tool Division) has become synonymous with advanced machining solutions, particularly with its 28, 33, and 45 series, each designed for specific industrial applications yet sharing common core features that enhance performance and productivity.

The MTD 28 series is primarily focused on precision machining for small to medium components. One of its standout features is the high-speed spindle technology, which supports a range of drilling and milling operations with minimal downtime. The machine is equipped with a robust structure designed to absorb vibrations, ensuring high precision and surface finish quality. Additionally, the MTD 28 integrates an intuitive user interface, allowing operators to navigate complex machining processes with ease. The series supports multiple tool configurations, enabling rapid changeovers and versatility in production.

Moving to the MTD 33 series, this model is engineered for medium to large production runs. A key characteristic of the MTD 33 is its advanced automation capabilities, including automatic tool changers and integrated robotic systems. These technologies streamline operations, reducing cycle times significantly. The series also boasts enhanced thermal stability, which is crucial for maintaining accuracy in high-speed machining environments. Furthermore, the MTD 33 utilizes an adaptive control system that adjusts machine parameters in real-time, optimizing performance based on workload and material type.

The MTD 45 series is the flagship among them, designed for high-performance machining tasks in heavy industry. It features an expansive workspace and a powerful drive system that allows for the machining of large components with exceptional torque. This series utilizes advanced CNC controls, ensuring precision that meets industry standards. The MTD 45 is also equipped with advanced coolant and lubrication systems, enhancing tool life and ensuring optimal cutting conditions. Moreover, this model supports a variety of machining processes, including turning, milling, and grinding, further solidifying its versatility in diverse manufacturing settings.

In summary, the MTD 28, 33, and 45 series exemplify innovative engineering and user-centric design. With features like high-speed spindles, automation capabilities, and robust construction, these machines cater to varying production needs while ensuring precision and efficiency. Whether for small component fabrication or large scale industrial applications, MTD’s commitment to technological advancement enables businesses to achieve greater productivity and quality in their machining processes.
Top Page Image Contents