Sears 536.884821 To USE Weight Transfer System, Track DRIVE/FREE-WHEEL Feature, Uftuphere, RG.12A

Page 12

OPERATION

...... 7IJIIIIMII

IIIjIIIIIILI] ii L

I'1 ill

i

TO USE WEIGHT TRANSFER SYSTEM

tn hardpacked or heavy snowconditions,conventional snowthrowerstendtorideup andleaveunevenmounds of snowbehind.Forthese conditions, yournewtracked snow throwerhas a uniqueweighttransfersystem (See Fig,,12) designedto minimize dde4Jp.

Theweight transfersystemengaged shiftsmoreweight to the auger housing,This weight transferkeeps the snow thrower in con*actwith the groundand reduces ride-upon ice and snow°

in lighter snow conditions or when transporting,you should release the weight transfer system for easier

steedng.

•To use the weighttransfer system,tilt up on upper handle untilbracket boltssnap intoplace in upper slotsof weighttransferpedal.

•To release,hold upperhandlefirmlyand pushdown onthe weighttransferpedalwiththebailof yourfool

NOTE: "[heweight transfersystemwill notwork if the auger housingheight adjust skids are adjustedto the highestposition.

TRACK DRIVE/FREE-WHEEL FEATURE

The tracksystemon yoursnowthrowerhasa ddvetlree- wheelfeature (See Fig 12A) whichallowstheunitto be transportedeasilywithoutthe enginebeingstarted.

•To use free_heeling, liftup the loopof the klickpin inthefronttrack wheel andpullthe pinouLInstallIhe pinthroughthe holein the shaftoutsideofthe track wheel Repeat on the oppositeside of the unit.

•To use normaldrive, liftthe loopoftheIdickpinfrom the outsidehole in the shaft.,Rotatethe fronttrack wheel untilthe hole in the trackwheel huband the

outsideholeintheshaftare irHine_Placepinthrough the bole in the track hub_Repeat on the opposite sideof the unit.

Ill Iiiiiiil:llljii i ]_ lIilliilgilllJ J........ II1'11ill II II

....................................

(Uftuphere)

WEIGHT TRANSFER

PEDAL UPPER SLOT'_

FIG.12

DRIVE WHEEL

RG.12A

NOTE:. tf unit does not move when engine is started, checkthepin locations°Pinson bothsidesofunitshould be in the normaldrive positionfor unitto move_

BEFORE STARTING THE ENGINE

FILL/ADD OIL:

The engineon this snow throwerwas shippedwithout oILAddoilbefore you startthe engine_Removetheoil lilt

cap!dipstickand fill the crank case to FULL line on d_pstick(about 20 ounces) (See Fig. 13) with SA, E. 10W-30motoroil(orequivalent)_Do not overfill. Tighten the fillcap/dipsticksecurelyeachtime youcheckthe oil level.

i

......... ..........

 

.....

'_ _tk_,',/'

BE1BETWEENFULL

AND ADD MARK

...........................................................................................................RGJ3 ..........................................................

!2

Page 11 Page 13
Image 12
Page 11 Page 13
Contents CRRFr$IRN Safety Rules Fuel SafetyBefore USE REPAIR/ADJUSTMENTS Safety Safe StorageMaintenance Agreement Optional AccessoryTable of Contents Contents of Shipping Carton Tools Required for AssemblyHOW to SET UP Your Snow Thrower To Remove Snow ThrowerRemovethe staples fromtop of carton Skids DOWN. this will HEt.P to PreventTo Install the Upper Handle and Crank Assembly Lightenuntil all bolts are in ptaceTjhtenlefthand side firstTo Checkjadjust Clutch Control Cables OffoffChute Deflector WEmHrTo Control Snow Discharge To Stop Your Snow ThrowerTo Move Forward and Backward To USE Weight Transfer System Track DRIVE/FREE-WHEEL FeatureUftuphere FILL/ADD OILTo Start Engine Fill GASMove the throttle controlupto RUN position Push the key into the ignition slot found in partsOperation Warm StartButton Frozen StarterGeneral Recommendations Snow ThrowerAfter First USE Lubrication Every TEN HoursEngine LubricationCheck the crankcase oil level See before Adjust To Adjust Skid HeightTo Adjust Chute Crank Assembly Once this clearance is set, tighten the nutsAdjustments To Adjust the Clutch Control CablesTo Adjust Belts Reinstallthe beltcover To Replace BeltsAuger Drive Belt Remove the beltcover See Fig,,26Service AN ,.,DJUSTMENTS To Adjust the Friction WheelTo Adjust the Belt Guides Traction Drive BeltTo Replace Friction Wheel Away from Fire or FlameFrom grease or oil To Adjust Track To Replace Auger Shear BoltSpacer provided FIG,.36SE CE a Adjust TS To Adjust CarburetorTo Adjust or Replace Spark Plug Engine Storage Snow Thrower StorageLubrication Other Areasare Still WarmService Service DatesLubrication Chart ScheduleShooting Points Trouble Cause CorrectionOtlflcult=tBllng I,iii Ii IHI Handle Assembly Repair Parts Craftsman 24 Snow ThrowerChute Control ROD Repair Parts Discharge Chute Repair Parts¸I Part NO. Part Name Part NO. Part NameAuger Housing Repair Parts 580773 Cover, Belt 71067 Flatwasher,518Ino IndicatesStandardHardwarettems70978 Screw, WaTap, 1/4-20xl/2 Ino Ref. ItrnHOo 580928 Frame 71393 Screw71100 70984Engine Components Repair Parts Drive Components Repair Parts Track Assembly Repair Parts Gear BOX Repair Parts Reri Decals Shift Yoke Repair Parts Partname Carburetor NO, 632107A Rewind Starter no E90600 !WaerDog, Starter Craftsman 4-CYCLE Engine 30968 20 326OO650488 65O883 Nut,P/w335 342A350 35tOtes When Ordering Repair PARTS, Always PRODUCT= =SNOWTHROWERPart Number Model Number
Top Page Image Contents