Sears 536.884821 General Recommendations, Snow Thrower, After First USE, Lubrication not Required

Page 15

MAINTENANCE

GENERAL RECOMMENDATIONS

The warrantyon thissnowthrowerdoes notcoveritems that have been subjectedto operator abuse or negli- gence,.To receivefull value from the warranty,operator must maintain snowthrower as instructedinthis manual.

Some adjustments will need to be made periodically to propedy mainlain your snow thrower,

All adjustments inthe Service and Adjustments section of this manual should be checked at feast once each

season,

AFTER FIRST USE

eCheck thetracks for tension and adjust if necessary (See To Adjust Track paragraph on page 23). Checkthe track adjustment and fasteners reguladyr

eBe sure that all tasteners are tight..

AS REQUIRED

The following adjustments should be performed more than once each season.

eAuger and Track Drive Belts shouid be adjusted alter the first 2 hours of use and again after 25 hours and at the beginning o! each season SeeTo Adjust Belts paragraph on page 19

eAll screws and nuts should be checked often to make sure they are tight, pre{erabty alter each use.

SNOW THROWER

LUBRICATION - EVERY TEN HOURS

Weight Transter System _Coat weight transler side plates with clinging type grease, such as Lubrip_ate, every ten (10) hours and before storage,, See Lu- brication Chart on page 26

eAuger Shaft- Using a hand greasegun,lubricatethe auger shaft zerk fittings (See A, Fig 16) every ten

(10)operating hours, Each time a shear bolt is replaced (see TO Replace Auger Shear Bolt para - graph on page 23), the augershaft MUSTbe greased,

eFor storage or when replacing shear boils, remove shear boils and lubricate auger shaft zed_s,,Rotate augers several times on the shaft and reinstal! the shear bolts.

LUBRICATION - NOT REQUIRED

eHex Shaft and Gears- Hex shaft and gears require nolubrication, Altbearings andbushings are liletime lubricated andrequireno maintenance (See Fig 17),,

NOTE: Any greasing or oiling of the above components can cause contamination ol the frictionwheel, Ifthe disc

driveplate or friction wheel come in contact with grease or oil, damage to the friction wheel will result,,

(PULL UP GENTLY AT CENTER)

FIG. 15

............,,r,;,,'r'"

FIG. 16

FRICTION

WHEEL

 

HEX

CHAINS

SHAFT

Should grease or oilcomein contactwith the discdrive plate or frictionwheel, be sure to clean the plate and wheel thoroughly_

NOTE: Forstorage,the hexshaft and gears shouldbe wipedwith10W-30motoroittopreventresting(See Fig..

17)_

eAuger Gear Box - The auger gear box has been factory lubricatedfor lite If for some reason lubri- cantshould leak out, have augergearcase checked by a competent repairrnan_

15

Image 15
Contents CRRFr$IRN Safety Rules Fuel SafetyBefore USE Safe Storage REPAIR/ADJUSTMENTS SafetyOptional Accessory Maintenance AgreementTable of Contents Tools Required for Assembly Contents of Shipping CartonSkids DOWN. this will HEt.P to Prevent HOW to SET UP Your Snow ThrowerTo Remove Snow Thrower Removethe staples fromtop of cartonLightenuntil all bolts are in ptaceTjhtenlefthand side first To Install the Upper Handle and Crank AssemblyOffoff To Checkjadjust Clutch Control CablesWEmHr Chute DeflectorTo Control Snow Discharge To Stop Your Snow ThrowerTo Move Forward and Backward FILL/ADD OIL To USE Weight Transfer SystemTrack DRIVE/FREE-WHEEL Feature UftupherePush the key into the ignition slot found in parts To Start EngineFill GAS Move the throttle controlupto RUN positionFrozen Starter OperationWarm Start ButtonLubrication Every TEN Hours General RecommendationsSnow Thrower After First USEEngine LubricationCheck the crankcase oil level See before Once this clearance is set, tighten the nuts AdjustTo Adjust Skid Height To Adjust Chute Crank AssemblyAdjustments To Adjust the Clutch Control CablesTo Adjust Belts Remove the beltcover See Fig,,26 Reinstallthe beltcoverTo Replace Belts Auger Drive BeltTraction Drive Belt Service AN ,.,DJUSTMENTSTo Adjust the Friction Wheel To Adjust the Belt GuidesTo Replace Friction Wheel Away from Fire or FlameFrom grease or oil FIG,.36 To Adjust TrackTo Replace Auger Shear Bolt Spacer providedSE CE a Adjust TS To Adjust CarburetorTo Adjust or Replace Spark Plug Areasare Still Warm Engine StorageSnow Thrower Storage Lubrication OtherSchedule ServiceService Dates Lubrication ChartShooting Points Trouble Cause CorrectionOtlflcult=tBllng I,iii Ii IHI Craftsman 24 Snow Thrower Handle Assembly Repair PartsPart NO. Part Name Chute Control ROD Repair PartsDischarge Chute Repair Parts ¸I Part NO. Part NameAuger Housing Repair Parts 580773 Cover, Belt 71067 Flatwasher,518Ino IndicatesStandardHardwarettems70978 Screw, WaTap, 1/4-20xl/2 Ino Ref. ItrnHOo 70984 580928 Frame71393 Screw 71100Engine Components Repair Parts Drive Components Repair Parts Track Assembly Repair Parts Gear BOX Repair Parts Reri Decals Shift Yoke Repair Parts Partname Carburetor NO, 632107A Rewind Starter no E90600 !WaerDog, Starter Craftsman 4-CYCLE Engine 65O883 Nut,P/w 3096820 326OO 65048835t 335342A 350Otes Model Number When Ordering Repair PARTS, AlwaysPRODUCT= =SNOWTHROWER Part Number