Sears 536.884821 manual To Install the Upper Handle and Crank Assembly

Page 8

i i

illll,

ii,i ii ,ll

....

,

i/ J iui

MBLY

TO INSTALL THE UPPER HANDLE AND CRANK ASSEMBLY

•Remove the screws,flatwashers,to.washers and hexnuts secudngthe shifterplate inthe lowerholes of the lower handle..

•Loosen,t_Jtdo not remove,thescrews,flatwashers,

lockwashers, and hex nuts in the upperholesof the lowerhandle_

•Raise upper handle into operatingposition.Upper, handleshouldbe to the outsideof the lower handle and shifterplate to the inside.

•Replacethe screws0flatwashers,lockwashers, and hex nutsthroughthehandlesandshifterplate.Do not

lightenuntil all bolts are in ptace_T'_jhtenlefthand side first.

NOTE: Unless you have the assistanceof anotherper- son,itmay be easierto install one sideofthehandleat the time.

•Tightenthe screw, flat'washer,Iockwasherand hex nut at the upper dght hand hole only (See Fig,4A),

•Remove the screw,flatwasher,Iockwasherand hex

nutfrom the upper lefthand holeofthe lowerhandle and discard,

•Remove the 3/8" nylon iocknutand flatwasherfrom theeye bolt assembly(on lhe chutecrank assembly eadier)_Check tomake surethetwo3/8"jamnutsare tight.The jam nuts shouldbe 3.75 inches fromthe endof the eye bolt (Fig. 4B).

•Install eye bolt through lower hole on the left hand side of the handle (See Fig.,4B)_

•Installthe 3/8" ftatwasherand the3/8" nylonlocknut looselyon the eye bolt as shownin Fig_4Bo

•Removetheptasticcap, thecotterpinandthewasher from the wormedend ofthe crank assemblyand set aside (See Fig°5)_

•Rotate the notched sectionof the dischargechute towardthe crank*adjustingrod..

•Installthe wormed end of thecrankthroughthe hole in the adjustingrod and securethe end with the flat washer and cotter pin, as shownin Fig. 5

•Bendthe ends of the cotter pin aroundthe rodand reinstallthe plasticcap.

•Tighten the eye bolt installedearlier, keepingeye in linewiththe rodwhiletighteningthe insidesecurely

•Make sure the outside3/8" jam nut is upagainstthe other3/8" jam nutand slidethebootoverthe adapter (See F_,.4B).

•Rotate the chute crank fully clockwiseand fully counter-clockwise,The discharge chute should rotatefullywith approximately 1/8 inchclearance betweenthe worm and the bottom of the notch(See

Fig. 5).

.................................................

_'tB"

FIG. 4A

=_

FIG. 5

•If the chute crank needs to be adjusted, go to the Service and Adjustments section on page 17_

Screwssecuringchuteclipsat thebase ofthechute shouldbe slightlyloose for easy rotation.

NOTE: Besurethe crankdoes nottouchthe sideofthe

engineor the coverwillbe scratched,:..................................................

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents CRRFr$IRN Before USE Safety RulesFuel Safety REPAIR/ADJUSTMENTS Safety Safe StorageMaintenance Agreement Optional AccessoryTable of Contents Contents of Shipping Carton Tools Required for AssemblyHOW to SET UP Your Snow Thrower To Remove Snow ThrowerRemovethe staples fromtop of carton Skids DOWN. this will HEt.P to PreventTo Install the Upper Handle and Crank Assembly Lightenuntil all bolts are in ptaceTjhtenlefthand side firstTo Checkjadjust Clutch Control Cables OffoffChute Deflector WEmHrTo Move Forward and Backward To Control Snow DischargeTo Stop Your Snow Thrower To USE Weight Transfer System Track DRIVE/FREE-WHEEL FeatureUftuphere FILL/ADD OILTo Start Engine Fill GASMove the throttle controlupto RUN position Push the key into the ignition slot found in partsOperation Warm StartButton Frozen StarterGeneral Recommendations Snow ThrowerAfter First USE Lubrication Every TEN HoursCheck the crankcase oil level See before EngineLubrication Adjust To Adjust Skid HeightTo Adjust Chute Crank Assembly Once this clearance is set, tighten the nutsTo Adjust Belts AdjustmentsTo Adjust the Clutch Control Cables Reinstallthe beltcover To Replace BeltsAuger Drive Belt Remove the beltcover See Fig,,26Service AN ,.,DJUSTMENTS To Adjust the Friction WheelTo Adjust the Belt Guides Traction Drive BeltFrom grease or oil To Replace Friction WheelAway from Fire or Flame To Adjust Track To Replace Auger Shear BoltSpacer provided FIG,.36To Adjust or Replace Spark Plug SE CE a Adjust TSTo Adjust Carburetor Engine Storage Snow Thrower StorageLubrication Other Areasare Still WarmService Service DatesLubrication Chart ScheduleOtlflcult=tBllng Shooting PointsTrouble Cause Correction I,iii Ii IHI Handle Assembly Repair Parts Craftsman 24 Snow ThrowerChute Control ROD Repair Parts Discharge Chute Repair Parts¸I Part NO. Part Name Part NO. Part NameAuger Housing Repair Parts 70978 Screw, WaTap, 1/4-20xl/2 Ino Ref. ItrnHOo 580773 Cover, Belt71067 Flatwasher,518Ino IndicatesStandardHardwarettems 580928 Frame 71393 Screw71100 70984Engine Components Repair Parts Drive Components Repair Parts Track Assembly Repair Parts Gear BOX Repair Parts Reri Decals Shift Yoke Repair Parts Partname Dog, Starter Carburetor NO, 632107A Rewind Starter noE90600 !Waer Craftsman 4-CYCLE Engine 30968 20 326OO650488 65O883 Nut,P/w335 342A350 35tOtes When Ordering Repair PARTS, Always PRODUCT= =SNOWTHROWERPart Number Model Number
Top Page Image Contents