Sears 536.884821 manual Craftsman 24 Snow Thrower, Handle Assembly Repair Parts

Page 28

CRAFTSMAN 24" SNOW THROWER 536.884821

HANDLE ASSEMBLY REPAIR PARTS

1!\

REF.

NO.	PART NOD	PART NAME
1	318457	Handte, Upper
2	4049	Bumper
3	307978	Auger Drive Lever, RH
4	307976	Traction Drive Lever, LH
5	3535	Nut, Push On Cap, 5/16 In.
6	302578	Pin, Clutch ftandle, Pivot
7	1579	Cable, Clutch

811234 Screw, Hex. 5/16-18 x 2-3/4 In.

971071 * Ratwasher. 11/32 in..

10 71060 Lockwasher` Split 5/16 In..

11 71037 " Nut, Hex. 5/16-18 TI_.

PARTNAME

Slop, Red Plastic, 5t16 In.

Screw. HHC, 5/16-18 x 2 In

Spring, Drive C_utch LH

Boot, Clutch Spdng

Nut, Hex Nyt, 11420 in

Screw, HHC, 5116-18 x 3/4 In.

Spdng, Auger Clutch RH

Hand{e. Lower

Bra_et, Shift

O',vnet'sManua}

Image 28

Contents CRRFr$IRN Fuel Safety Safety RulesBefore USE REPAIR/ADJUSTMENTS Safety Safe StorageMaintenance Agreement Optional AccessoryTable of Contents Contents of Shipping Carton Tools Required for AssemblyHOW to SET UP Your Snow Thrower To Remove Snow ThrowerRemovethe staples fromtop of carton Skids DOWN. this will HEt.P to PreventTo Install the Upper Handle and Crank Assembly Lightenuntil all bolts are in ptaceTjhtenlefthand side firstTo Checkjadjust Clutch Control Cables OffoffChute Deflector WEmHrTo Stop Your Snow Thrower To Control Snow DischargeTo Move Forward and Backward To USE Weight Transfer System Track DRIVE/FREE-WHEEL FeatureUftuphere FILL/ADD OILTo Start Engine Fill GASMove the throttle controlupto RUN position Push the key into the ignition slot found in partsOperation Warm StartButton Frozen StarterGeneral Recommendations Snow ThrowerAfter First USE Lubrication Every TEN HoursLubrication EngineCheck the crankcase oil level See before Adjust To Adjust Skid HeightTo Adjust Chute Crank Assembly Once this clearance is set, tighten the nutsTo Adjust the Clutch Control Cables AdjustmentsTo Adjust Belts Reinstallthe beltcover To Replace BeltsAuger Drive Belt Remove the beltcover See Fig,,26Service AN ,.,DJUSTMENTS To Adjust the Friction WheelTo Adjust the Belt Guides Traction Drive BeltAway from Fire or Flame To Replace Friction WheelFrom grease or oil To Adjust Track To Replace Auger Shear BoltSpacer provided FIG,.36To Adjust Carburetor SE CE a Adjust TSTo Adjust or Replace Spark Plug Engine Storage Snow Thrower StorageLubrication Other Areasare Still WarmService Service DatesLubrication Chart ScheduleTrouble Cause Correction Shooting PointsOtlflcult=tBllng I,iii Ii IHI Handle Assembly Repair Parts Craftsman 24 Snow ThrowerChute Control ROD Repair Parts Discharge Chute Repair Parts¸I Part NO. Part Name Part NO. Part NameAuger Housing Repair Parts 71067 Flatwasher,518Ino IndicatesStandardHardwarettems 580773 Cover, Belt70978 Screw, WaTap, 1/4-20xl/2 Ino Ref. ItrnHOo 580928 Frame 71393 Screw71100 70984Engine Components Repair Parts Drive Components Repair Parts Track Assembly Repair Parts Gear BOX Repair Parts Reri Decals Shift Yoke Repair Parts Partname E90600 !Waer Carburetor NO, 632107A Rewind Starter noDog, Starter Craftsman 4-CYCLE Engine 30968 20 326OO650488 65O883 Nut,P/w335 342A350 35tOtes When Ordering Repair PARTS, Always PRODUCT= =SNOWTHROWERPart Number Model Number

CRAFTSMAN 24" SNOW THROWER 536.884821

HANDLE ASSEMBLY REPAIR PARTS

1579

811234 Screw, Hex. 5/16-18 x 2-3/4 In.

971071 * Ratwasher. 11/32 in..