Sears 536.884821 manual To Replace Belts, Auger Drive Belt, Remove the beltcover See Fig,,26

Page 19

i1,,,,i

i

i

iiii,

,.SERVICE AND

TO REPLACE BELTS

The drive belts on this snow thrower are o! special construction and should be replaced with original equipment belts available from your nearest SEARS Store or Service Center_

You will need the assistanceof a second person while replacing the belts°

Drain the gasoline from the fueltankby removing the fuel line., Drain the gas and reinstall fuel line,,

AUGER DRIVE BELT

If your snow throwerwilt not discharge snow, and the auger drive belt isdamaged, replace it as to!lows:

®Disconnect the sparkplugwire.

o Remove the beltcover (See Fig,,26).

®Loosenthe belt guides (See Fig°27) and pullaway from the drivepulley.

eLoosen the auger idler pulley(See Fig. 28) and slip the belt out.,

eRemove top two bolls that secure auger housing to motor mount frame. Loosen bottom two bolts.,

Auger housing andmotormountIrame willseparate hinged by bottom two bolts.

eRemove brake arm from housing, Do not remove spdng,

eRemove the belt fromthe augerdrive engine pulley

eInstall the original equipmentreplacement bell in reverse order of removal,

eReinstall brake arm intohousing,,Insure brake arm

isfullyinsertedinto housingand brake pad is riding in pulley groove°

0Position drive belt onto the auger drive putley,

0Adjust thedr_vebelt (seeTo AdjustAuger Drive Belt paragraph on page 18),,

0Adjust the belt guides (see To Adjust The Belt Guides paragraphon page 20)+

0Reinstallthe beltcover.

OCheck clutch control cable adjustment (see page 18)+

Reconnect the spark plug wire,,

GUIDE

(Lalt Hand)

AUGER

DRIVE

(Right Hand)

BELT

:R DRIVE

TRACTION DRIVE

PULLEY

 

IDLER PULLEY

 

 

PULLEY

FIG, 27

!11'll_j II I

_32

BELT

GUIDE

 

 

Hand)

{Righ! Hand)

3/32

INCH

AUGER

 

 

PULLEY ENGAGED

 

 

 

 

IMPELLER

 

 

PUL L_Y

,,i,, iii

,lira i,,,,11,

 

 

FIG. 28

 

19

Image 19
Contents CRRFr$IRN Fuel Safety Safety RulesBefore USE Safe Storage REPAIR/ADJUSTMENTS SafetyOptional Accessory Maintenance AgreementTable of Contents Tools Required for Assembly Contents of Shipping CartonSkids DOWN. this will HEt.P to Prevent HOW to SET UP Your Snow ThrowerTo Remove Snow Thrower Removethe staples fromtop of cartonLightenuntil all bolts are in ptaceTjhtenlefthand side first To Install the Upper Handle and Crank AssemblyOffoff To Checkjadjust Clutch Control CablesWEmHr Chute DeflectorTo Stop Your Snow Thrower To Control Snow DischargeTo Move Forward and Backward FILL/ADD OIL To USE Weight Transfer SystemTrack DRIVE/FREE-WHEEL Feature UftupherePush the key into the ignition slot found in parts To Start EngineFill GAS Move the throttle controlupto RUN positionFrozen Starter OperationWarm Start ButtonLubrication Every TEN Hours General RecommendationsSnow Thrower After First USELubrication EngineCheck the crankcase oil level See before Once this clearance is set, tighten the nuts AdjustTo Adjust Skid Height To Adjust Chute Crank AssemblyTo Adjust the Clutch Control Cables AdjustmentsTo Adjust Belts Remove the beltcover See Fig,,26 Reinstallthe beltcoverTo Replace Belts Auger Drive BeltTraction Drive Belt Service AN ,.,DJUSTMENTSTo Adjust the Friction Wheel To Adjust the Belt GuidesAway from Fire or Flame To Replace Friction WheelFrom grease or oil FIG,.36 To Adjust TrackTo Replace Auger Shear Bolt Spacer providedTo Adjust Carburetor SE CE a Adjust TSTo Adjust or Replace Spark Plug Areasare Still Warm Engine StorageSnow Thrower Storage Lubrication OtherSchedule ServiceService Dates Lubrication ChartTrouble Cause Correction Shooting PointsOtlflcult=tBllng I,iii Ii IHI Craftsman 24 Snow Thrower Handle Assembly Repair PartsPart NO. Part Name Chute Control ROD Repair PartsDischarge Chute Repair Parts ¸I Part NO. Part NameAuger Housing Repair Parts 71067 Flatwasher,518Ino IndicatesStandardHardwarettems 580773 Cover, Belt70978 Screw, WaTap, 1/4-20xl/2 Ino Ref. ItrnHOo 70984 580928 Frame71393 Screw 71100Engine Components Repair Parts Drive Components Repair Parts Track Assembly Repair Parts Gear BOX Repair Parts Reri Decals Shift Yoke Repair Parts Partname E90600 !Waer Carburetor NO, 632107A Rewind Starter noDog, Starter Craftsman 4-CYCLE Engine 65O883 Nut,P/w 3096820 326OO 65048835t 335342A 350Otes Model Number When Ordering Repair PARTS, AlwaysPRODUCT= =SNOWTHROWER Part Number