Sears 536.884821 manual Maintenance Agreement, Optional Accessory

Page 4

CONGRATULATIONS on your purchase of a Sears CraftsmanSnow _rower_ It hasbeen designed,engi- neeredand manufactured to give you the bestpossible dependabilityand performance.

Shouldyou experienceany problemyou cannot easily remedy, please contact your nearest Sears Service Center/Department. We have competent,welt4rained techniciansand the propertoolsto se_ce or repairthis uniL

Pleaseread and retainthis manual. 'Theinstructionswill enableyouto assembleand maintainyoursnowthrower _mpedy. Alwaysobservethe =SAFETY RULES."

MODEL

NUMBER 536_884821

SERIAL

NUMBER

DATE OF

PURCHASE

THE MODEL AND SERIAL NUMBERS WiLL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING_

YOU SHOULD RECORD BOTH SERIALNUMBER

AND DATE OF PURCHASEAND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE°

MAINTENANCE AGREEMENT

A Sears Maintenance Agreement is available on this product, Contactyournearest Sears Storefor details_

PRODUCT SPECIFICATIONS

_SE POWER:

5 hp

 

: :

:- ,,,,,,,,,,,,,,

 

 

DISPLACEMENT:

10.49

 

 

 

cu. In.

 

GASOLINE CAPACITY:

2 quart

 

 

 

Unleaded

........... m

,,,,,,,,,

-

......... Hi

OIL (20 oz., Capacity):

SAE 10W-30 or

 

 

5W-30"

 

SPARK PLUG :

Champion

(GAP

.030 In.)

RJ19LM

 

VALVE CLEARANCE:

Intake:

.010 In.

 

 

Exhaust:

.010 in.

"S.AIF...5W-30 motor O" maybe used to make

starting easier In areas where the temperature Is 20° F or lower.

OPTIONAL ACCESSORY

An electricstarterkit(StockNo.,71-8894) is available for

this snowthrower and may be ordered throughSears Retailor CatologStores Installation instructions for the electricstarter are includedin thiskit.

CUSTOMER RESPONSIBILITIES

•Read and observethe safety rules°

•Followa regularschedulein maintaining,caring tot and usingyoursnowthrower.,

•FolJowthe instructions under "Maintenance"and =Storage"sectionsof thisowner'smanual

TWO YEAR LIMITED WARRANTY ON CRAFTSMAN

SNOW THROWER

Fortwo yearsfrom the date of purchase,when this Craftsman Snow Throweris maintained,lubricated and tuned-upaccordingto the instructionsin the owner'smanual,Searswitl repair,free of charge, any detect in materialand workmanship.

It this CraftsmanSnow Throweris usedfor commercialor rentalpurposes,this warrantyappliesfor only 90 days from the date of purchase.

This warrantydoes not coverthe following:

•Expendableitemswhichbecome worndudngnormaluse, such as spark plugs,ddve belts and shear p_so

Repairsnecessarybecause of operatorabuse or negligence,including bent crankshaftsand the failure to maintainthe equipmentaccordingto the instructionscontainedin the owner'smanual.

WARRANTY'SERVICE IS AVAILABLEBY RETURNING THE CRAFTSMAN SNOW THROWER TO THE NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. THIS WARRANTY

APPLIES ONLY WHILE THIS PRODUCT IS IN USE iN THE UNITED STATES,

Thiswan_antygivesyou speciticlegal rights,and youmay also have otherdghts whichmay varyfrom state to state.

SEARS, ROEBUCK AND CO. Department731CR_W,Sears Tower, Chicago,tL60684 ...................

..........: ::

............,,,J=,

i

.....

,,,

,,,,,,

i uH=

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents CRRFr$IRN Fuel Safety Safety RulesBefore USE REPAIR/ADJUSTMENTS Safety Safe StorageMaintenance Agreement Optional AccessoryTable of Contents Contents of Shipping Carton Tools Required for AssemblyHOW to SET UP Your Snow Thrower To Remove Snow ThrowerRemovethe staples fromtop of carton Skids DOWN. this will HEt.P to PreventTo Install the Upper Handle and Crank Assembly Lightenuntil all bolts are in ptaceTjhtenlefthand side firstTo Checkjadjust Clutch Control Cables OffoffChute Deflector WEmHrTo Stop Your Snow Thrower To Control Snow DischargeTo Move Forward and Backward To USE Weight Transfer System Track DRIVE/FREE-WHEEL FeatureUftuphere FILL/ADD OILTo Start Engine Fill GASMove the throttle controlupto RUN position Push the key into the ignition slot found in partsOperation Warm StartButton Frozen StarterGeneral Recommendations Snow ThrowerAfter First USE Lubrication Every TEN HoursLubrication EngineCheck the crankcase oil level See before Adjust To Adjust Skid HeightTo Adjust Chute Crank Assembly Once this clearance is set, tighten the nutsTo Adjust the Clutch Control Cables AdjustmentsTo Adjust Belts Reinstallthe beltcover To Replace BeltsAuger Drive Belt Remove the beltcover See Fig,,26Service AN ,.,DJUSTMENTS To Adjust the Friction WheelTo Adjust the Belt Guides Traction Drive BeltAway from Fire or Flame To Replace Friction WheelFrom grease or oil To Adjust Track To Replace Auger Shear BoltSpacer provided FIG,.36To Adjust Carburetor SE CE a Adjust TSTo Adjust or Replace Spark Plug Engine Storage Snow Thrower StorageLubrication Other Areasare Still WarmService Service DatesLubrication Chart ScheduleTrouble Cause Correction Shooting PointsOtlflcult=tBllng I,iii Ii IHI Handle Assembly Repair Parts Craftsman 24 Snow ThrowerChute Control ROD Repair Parts Discharge Chute Repair Parts¸I Part NO. Part Name Part NO. Part NameAuger Housing Repair Parts 71067 Flatwasher,518Ino IndicatesStandardHardwarettems 580773 Cover, Belt70978 Screw, WaTap, 1/4-20xl/2 Ino Ref. ItrnHOo 580928 Frame 71393 Screw71100 70984Engine Components Repair Parts Drive Components Repair Parts Track Assembly Repair Parts Gear BOX Repair Parts Reri Decals Shift Yoke Repair Parts Partname E90600 !Waer Carburetor NO, 632107A Rewind Starter noDog, Starter Craftsman 4-CYCLE Engine 30968 20 326OO650488 65O883 Nut,P/w335 342A350 35tOtes When Ordering Repair PARTS, Always PRODUCT= =SNOWTHROWERPart Number Model Number
Top Page Image Contents