Cub Cadet Two Stage Snow Thrower warranty Auger Belt Replacement

Page 17

Auger Belt Replacement

To remove and replace your snow thrower’s auger belt, proceed as follows:

1.Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. See Figure 6-4.

Figure 6-4

Figure 6-5

Figure 6-6

NOTE: Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

2.Carefully pivot the snow thrower up and forward so that it rests on the auger housing. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Figure 6-5.

3.Roll the auger belt off the engine pulley. See Figure 6-6.

4.a. Loosen and remove the shoulder screw which acts as a belt keeper. See Figure 6-7.

b.Unhook the support bracket spring from the frame.

5.Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. Reassemble auger belt by following instructions in reverse order. See Figure 6-8.

NOTE: Do NOT forget to reinstall the shoulder screw and reconnect the spring to the frame after installing a replacement auger belt and to remove the piece of plastic from under the gas cap.

Figure 6-7

Figure 6-8

6

Maintaining

Your Snow

Thrower

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi- viscosity oils also result in higher oil consump- tion when used above 32ºF (0ºC). Check your snow thrower’s engine oil level more frequently to avoid possible engine damage from running low on oil.

NOTE: Do not sand- blast spark plug. Spark plug should be cleaned by scraping or wire brushing and washing with a commercial solvent.

IMPORTANT NEVER replace the auger shear pins with standard pins. Any damage to the auger gearbox or other com- ponents, as a result of doing so, will NOT be covered by your snow thrower’s warranty.

17

Image 17
Contents Ottawa Street South, KITCHENER, Ontario N2G 4J1 Two-Stage Snow Thrower769-03263 06/06/07Customer Support Table of ContentsFinding and Recording Model Number Your Responsibility Restrict the use Chute Clean-out ToolTraining Safe Operation PracticesPreparation Your ResponsibilityOperation Maintenance & StorageDo not modify engine Average Useful LifeSetting Up Shear Pin Storage optional Setting Up Your Snow ThrowerAll models Drift Cutters If EquippedSnowthrower Model Lamp Wiring Harness If equipped Clean-Out ToolSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Electric Starter If Equipped Gas & Oil Fill-UpStopping The Engine To Engage Augers To Engage DriveRecoil Starter Auger Control TestShift Cable Making AdjustmentsChute Control Drive Control & Shift LeverReversible Steel Skid Shoe Reversible Plastic Skid ShoeEngine Maintaining Your Snow ThrowerLubrication Shave Plate and Skid ShoesUnhook the support bracket spring from the frame Auger Belt ReplacementRoll the auger belt off the engine pulley. See Figure Remove and replace belt in the reverse order Drive Belt ReplacementRemove the rubber ring from between the plates Friction Wheel RemovalWipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting10.30.06 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce Remarque Lhabitacle peut être légèrement différent 30 in/poPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Commerciale Utilisation GarantieDépannage Solution Causes ProblèmeCarburant le Videz Gaz Propre etSouffleuse ’entretien Régime Tarières De courroie la de RemplacementTransmission Régime ’entretienMoteur Patins et plate LameLubrification Réglages Tarière la de CommandePatins Plastique en réversible Patins 4-5 FigureGoulotte la de Commande Et transmission la de CommandeVitesses de levier Vitesses de changement de CâbleMain SouffleuseToucher 150F dépasserModèles certains sur électrique Démarreur ’huile et d’essence PleinsModèles Certains sur électrique DémarreurTarières Trans de commande la de BlocageLa de proximité à Souffleuse la’essence plein le jamais faites Ne Souffleuse la de CommandesDépart de Volet Goulotte la de dégagement de Outil Général d’ordre RecommandationsPneumatiques Bandages pneus des Pression Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Employer à moteur à l’huile à et carburant au InférieurQuant moteur du d’utilisation notice la consulter veuillez ’assemblage Après .ESSENCE Sans mais d’huile pleinResponsabilité Votre Remisage et EntretienMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation UtilisationFormation Responsabilité VotreDe Outil Est goulotte la de dégagement de outil UnModèle de numéro le trouver Pour Vente-après ServiceMatières des Table ’utilisation La voir détachées Pièces03263-769 Phases deux neige à Souffleuse4J1 N2G Ontario KITCHENER, South, Street Ottawa

Two Stage Snow Thrower specifications

The Cub Cadet Two Stage Snow Thrower is an exceptional piece of equipment designed to tackle the challenges of winter weather with efficiency and ease. This powerful snow removal machine is engineered to provide high-performance snow clearing, making it an essential tool for homeowners dealing with heavy snowfall.

One of the standout features of the Cub Cadet Two Stage Snow Thrower is its robust engine. Equipped with a reliable, heavy-duty engine, this snow thrower delivers exceptional torque and ensures seamless operation even under the most challenging conditions. The engine's efficiency contributes to its ability to clear snow quickly, making it ideal for large driveways and sidewalks.

The two-stage system is another hallmark of this machine. Utilizing an auger and impeller system, the snow thrower can efficiently gather and throw snow a considerable distance away, preventing snow from piling up in unwanted areas. This dual-action mechanism allows for faster clearing times and less manual labor, as it effectively handles both light flurries and heavy, wet snow.

Cub Cadet incorporates advanced technologies in their snow thrower designs. One notable feature is the push-button electric start, which eliminates the hassle of manual starting, especially in frigid temperatures. This convenience ensures that users can quickly power up the machine and begin their snow-clearing tasks without delay.

In terms of control, this model offers intuitive handling and customizable settings. The adjustable skid shoes allow users to modify the clearing height, ensuring effective operation on various surfaces, including driveways, sidewalks, and gravel. Additionally, the six-speed forward and two-speed reverse settings provide optimal maneuverability, allowing users to navigate tight spaces and tricky terrain with ease.

The snow thrower also features ergonomic handles with easy-grip controls, ensuring comfort during extended use. The built-in LED headlights enhance visibility in low-light conditions, allowing users to operate the machine safely during early morning or late evening snow removal.

Durability is a key characteristic of the Cub Cadet Two Stage Snow Thrower. Its solid construction, reinforced housing, and high-quality materials ensure that this equipment can withstand harsh winter conditions year after year. With comprehensive maintenance schedules and readily available customer support, owners can rest assured that their investment is protected.

In summary, the Cub Cadet Two Stage Snow Thrower combines power, innovation, and user-friendly features, making it a top choice for efficient snow removal. Its robust engine, two-stage system, and advanced technology make tackling winter weather more manageable than ever.