Cub Cadet Two Stage Snow Thrower warranty Setting Up

Page 6

3

Setting Up

A

Your Snow

 

Thrower

B

NOTE: References to

 

right or left side of the

Figure 3-1

snow thrower are deter-

 

mined from behind the

 

unit in the operating

 

position.

 

NOTE: This Operator’s

 

Manual covers several

 

models, handle panels,

 

lights and chute cranks

 

are some features that

 

may vary by model.

 

Not all features refer-

 

enced in this manual

 

are applicable to all

 

snow thrower models.

Figure 3-2

NOTE: Two replace- ment auger shear pins are included with this manual (or stowed

in the plastic handle panel). Refer to Augers in the Maintainance Section for more information regarding shear pin replacement.

Figure 3-3

IMPORTANT: The snow thrower is shipped with oil and WITHOUT GASOLINE. After assembly, refer to separate engine manual for proper fuel and engine oil recommendations.

1.Observe the lower area of the snow thrower to be sure both cables are aligned with roller guides.

a.Pull up and back on upper handle as shown in Figure 3-1. Align upper handle with the lower handle.

b.Tighten hand knobs securing upper handle to lower handle.

2.Remove wing nut and hex screw from chute control assembly and clevis pin and cotter pin from chute support bracket. See Figure 3-2. Position the chute assembly (forward-facing) over the chute base.

3.Place chute assembly onto chute base and secure chute control assembly to chute support bracket with clevis pin and cotter pin removed earlier. See Figure 3-3.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents
769-03263 Two-Stage Snow ThrowerOttawa Street South, KITCHENER, Ontario N2G 4J1 06/06/07Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Your Responsibility Restrict the usePreparation Safe Operation PracticesTraining Your ResponsibilityDo not modify engine Maintenance & StorageOperation Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalDrift Cutters If Equipped Snowthrower ModelAll models Skid Shoes Clean-Out ToolLamp Wiring Harness If equipped Tire Pressure Pneumatic TiresOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Stopping The EngineElectric Starter If Equipped Recoil Starter To Engage DriveTo Engage Augers Auger Control TestChute Control Making AdjustmentsShift Cable Drive Control & Shift LeverReversible Plastic Skid Shoe Reversible Steel Skid ShoeLubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Remove and replace belt in the reverse orderFriction Wheel Removal Remove the rubber ring from between the platesOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 10.30.06Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différentPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Garantie Commerciale UtilisationSolution Causes Problème DépannagePropre et SouffleuseCarburant le Videz Gaz ’entretien Régime De courroie la de Remplacement TransmissionTarières ’entretien RégimePatins et plate Lame LubrificationMoteur Patins Tarière la de CommandeRéglages Plastique en réversible Patins 4-5 FigureVitesses de levier Et transmission la de CommandeGoulotte la de Commande Vitesses de changement de CâbleToucher SouffleuseMain 150F dépasserModèles ’huile et d’essence PleinsModèles certains sur électrique Démarreur Certains sur électrique DémarreurLa de proximité à Trans de commande la de BlocageTarières Souffleuse laSouffleuse la de Commandes Départ de Volet’essence plein le jamais faites Ne Pneumatiques Bandages pneus des Pression Général d’ordre RecommandationsGoulotte la de dégagement de Outil Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Quant moteur du d’utilisation notice la consulter veuillez InférieurEmployer à moteur à l’huile à et carburant au ’assemblage Après .ESSENCE Sans mais d’huile pleinMoyenne utile vie de Durée Remisage et EntretienResponsabilité Votre Gaz de émissions les concernant AvisFormation UtilisationPréparation Responsabilité VotreEst goulotte la de dégagement de outil Un De OutilMatières des Table Vente-après ServiceModèle de numéro le trouver Pour ’utilisation La voir détachées PiècesPhases deux neige à Souffleuse 4J1 N2G Ontario KITCHENER, South, Street Ottawa03263-769