Cub Cadet Two Stage Snow Thrower warranty Maintaining Your Snow Thrower, Engine, Lubrication

Page 16

6

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing, or inspect- ing, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Engine

Refer to the separate engine manual packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.

1.Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

2.Remove the lower frame cover by removing the two screws which secure it.

3.Apply a light coating of an all-weather multi-purpose oil to the hex shaft. See Figure 6-1.

NOTE: Avoid getting oil on rubber friction wheel and aluminum drive plate.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Chute Directional Control (optional)

Once a season, the joystick should be lubricated with petroleum jelly, linseed oil, mineral oil, paraffin wax or 3-in-1 oil.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 6-2.

 

Figure 6-1

 

3HEARE0IN

3PACERS

"EARING

 

 

 

Figure 6-2

 

Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1. Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2. Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 6-3.

To remove shave plate:

1. Remove the carriage bolts and hex nuts which attach

 

it and the skid shoes to the snow thrower housing.

Figure 6-3

 

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Two-Stage Snow Thrower Ottawa Street South, KITCHENER, Ontario N2G 4J1769-03263 06/06/07Finding and Recording Model Number Table of ContentsCustomer Support Chute Clean-out Tool Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalSnowthrower Model Drift Cutters If EquippedAll models Clean-Out Tool Lamp Wiring Harness If equippedSkid Shoes Tire Pressure Pneumatic TiresOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped To Engage Drive To Engage AugersRecoil Starter Auger Control TestMaking Adjustments Shift CableChute Control Drive Control & Shift LeverReversible Plastic Skid Shoe Reversible Steel Skid ShoeMaintaining Your Snow Thrower EngineLubrication Shave Plate and Skid ShoesRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Drive Belt Replacement Remove and replace belt in the reverse orderFriction Wheel Removal Remove the rubber ring from between the platesOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 10.30.06Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différentPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Garantie Commerciale UtilisationSolution Causes Problème DépannageSouffleuse Propre etCarburant le Videz Gaz ’entretien Régime Transmission De courroie la de RemplacementTarières ’entretien RégimeLubrification Patins et plate LameMoteur Tarière la de Commande RéglagesPatins Plastique en réversible Patins 4-5 FigureEt transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleSouffleuse MainToucher 150F dépasser’huile et d’essence Pleins Modèles certains sur électrique DémarreurModèles Certains sur électrique DémarreurTrans de commande la de Blocage TarièresLa de proximité à Souffleuse laDépart de Volet Souffleuse la de Commandes’essence plein le jamais faites Ne Général d’ordre Recommandations Goulotte la de dégagement de OutilPneumatiques Bandages pneus des Pression Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Inférieur Employer à moteur à l’huile à et carburant auQuant moteur du d’utilisation notice la consulter veuillez ’assemblage Après .ESSENCE Sans mais d’huile pleinRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisUtilisation PréparationFormation Responsabilité VotreEst goulotte la de dégagement de outil Un De OutilVente-après Service Modèle de numéro le trouver PourMatières des Table ’utilisation La voir détachées Pièces4J1 N2G Ontario KITCHENER, South, Street Ottawa Phases deux neige à Souffleuse03263-769

Two Stage Snow Thrower specifications

The Cub Cadet Two Stage Snow Thrower is an exceptional piece of equipment designed to tackle the challenges of winter weather with efficiency and ease. This powerful snow removal machine is engineered to provide high-performance snow clearing, making it an essential tool for homeowners dealing with heavy snowfall.

One of the standout features of the Cub Cadet Two Stage Snow Thrower is its robust engine. Equipped with a reliable, heavy-duty engine, this snow thrower delivers exceptional torque and ensures seamless operation even under the most challenging conditions. The engine's efficiency contributes to its ability to clear snow quickly, making it ideal for large driveways and sidewalks.

The two-stage system is another hallmark of this machine. Utilizing an auger and impeller system, the snow thrower can efficiently gather and throw snow a considerable distance away, preventing snow from piling up in unwanted areas. This dual-action mechanism allows for faster clearing times and less manual labor, as it effectively handles both light flurries and heavy, wet snow.

Cub Cadet incorporates advanced technologies in their snow thrower designs. One notable feature is the push-button electric start, which eliminates the hassle of manual starting, especially in frigid temperatures. This convenience ensures that users can quickly power up the machine and begin their snow-clearing tasks without delay.

In terms of control, this model offers intuitive handling and customizable settings. The adjustable skid shoes allow users to modify the clearing height, ensuring effective operation on various surfaces, including driveways, sidewalks, and gravel. Additionally, the six-speed forward and two-speed reverse settings provide optimal maneuverability, allowing users to navigate tight spaces and tricky terrain with ease.

The snow thrower also features ergonomic handles with easy-grip controls, ensuring comfort during extended use. The built-in LED headlights enhance visibility in low-light conditions, allowing users to operate the machine safely during early morning or late evening snow removal.

Durability is a key characteristic of the Cub Cadet Two Stage Snow Thrower. Its solid construction, reinforced housing, and high-quality materials ensure that this equipment can withstand harsh winter conditions year after year. With comprehensive maintenance schedules and readily available customer support, owners can rest assured that their investment is protected.

In summary, the Cub Cadet Two Stage Snow Thrower combines power, innovation, and user-friendly features, making it a top choice for efficient snow removal. Its robust engine, two-stage system, and advanced technology make tackling winter weather more manageable than ever.
Top Page Image Contents