Cub Cadet Two Stage Snow Thrower warranty Off-Season Storage

Page 20

7

Off-Season

Storage

WARNING

Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

Drain fuel into an approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

Do not drain carburetor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

Observe the following, when preparing your snow thrower for off-season storage:

•Drain fuel into an approved container outdoors, away from any open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes and other sources of ignition prior to draining fuel. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

•If unit is to be stored over 30 days, prepare for storage as instructed in the separate engine manual packed with your unit.

•Run engine until fuel tank is empty and engine stops due to lack of fuel.

•Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.

•Drain carburetor by pressing upward on bowl drain, located below the carburetor cover.

•Fuel stabilizers, such as STA-BIL®, are an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Do not drain carburetor if using a fuel stabilizer.

•Wipe equipment with an oiled rag to prevent rust.

•Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover spark plug hole with rag. Crank engine several times to distribute oil. Replace spark plug.

•Follow the lubrication recommendations found in the Maintenance Section.

•Always store the snow thrower in a clean, dry area.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Two-Stage Snow Thrower Ottawa Street South, KITCHENER, Ontario N2G 4J1769-03263 06/06/07Customer Support Table of ContentsFinding and Recording Model Number Chute Clean-out Tool Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Setting Up Your Snow Thrower Shear Pin Storage optionalAll models Drift Cutters If EquippedSnowthrower Model Clean-Out Tool Lamp Wiring Harness If equippedSkid Shoes Tire Pressure Pneumatic TiresOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Electric Starter If Equipped Gas & Oil Fill-UpStopping The Engine To Engage Drive To Engage AugersRecoil Starter Auger Control TestMaking Adjustments Shift CableChute Control Drive Control & Shift LeverReversible Plastic Skid Shoe Reversible Steel Skid ShoeMaintaining Your Snow Thrower EngineLubrication Shave Plate and Skid ShoesUnhook the support bracket spring from the frame Auger Belt ReplacementRoll the auger belt off the engine pulley. See Figure Drive Belt Replacement Remove and replace belt in the reverse orderFriction Wheel Removal Remove the rubber ring from between the platesOff-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 10.30.06Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce 30 in/po Remarque Lhabitacle peut être légèrement différentPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Garantie Commerciale UtilisationSolution Causes Problème DépannageCarburant le Videz Gaz Propre etSouffleuse ’entretien Régime Tarières De courroie la de RemplacementTransmission ’entretien RégimeMoteur Patins et plate LameLubrification Tarière la de Commande RéglagesPatins Plastique en réversible Patins 4-5 FigureEt transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleSouffleuse MainToucher 150F dépasser’huile et d’essence Pleins Modèles certains sur électrique DémarreurModèles Certains sur électrique DémarreurTrans de commande la de Blocage TarièresLa de proximité à Souffleuse la’essence plein le jamais faites Ne Souffleuse la de CommandesDépart de Volet Général d’ordre Recommandations Goulotte la de dégagement de OutilPneumatiques Bandages pneus des Pression Goulotte la de dégagement de OutilÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage Inférieur Employer à moteur à l’huile à et carburant auQuant moteur du d’utilisation notice la consulter veuillez ’assemblage Après .ESSENCE Sans mais d’huile pleinRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisUtilisation PréparationFormation Responsabilité VotreEst goulotte la de dégagement de outil Un De OutilVente-après Service Modèle de numéro le trouver PourMatières des Table ’utilisation La voir détachées Pièces03263-769 Phases deux neige à Souffleuse4J1 N2G Ontario KITCHENER, South, Street Ottawa

Two Stage Snow Thrower specifications

The Cub Cadet Two Stage Snow Thrower is an exceptional piece of equipment designed to tackle the challenges of winter weather with efficiency and ease. This powerful snow removal machine is engineered to provide high-performance snow clearing, making it an essential tool for homeowners dealing with heavy snowfall.

One of the standout features of the Cub Cadet Two Stage Snow Thrower is its robust engine. Equipped with a reliable, heavy-duty engine, this snow thrower delivers exceptional torque and ensures seamless operation even under the most challenging conditions. The engine's efficiency contributes to its ability to clear snow quickly, making it ideal for large driveways and sidewalks.

The two-stage system is another hallmark of this machine. Utilizing an auger and impeller system, the snow thrower can efficiently gather and throw snow a considerable distance away, preventing snow from piling up in unwanted areas. This dual-action mechanism allows for faster clearing times and less manual labor, as it effectively handles both light flurries and heavy, wet snow.

Cub Cadet incorporates advanced technologies in their snow thrower designs. One notable feature is the push-button electric start, which eliminates the hassle of manual starting, especially in frigid temperatures. This convenience ensures that users can quickly power up the machine and begin their snow-clearing tasks without delay.

In terms of control, this model offers intuitive handling and customizable settings. The adjustable skid shoes allow users to modify the clearing height, ensuring effective operation on various surfaces, including driveways, sidewalks, and gravel. Additionally, the six-speed forward and two-speed reverse settings provide optimal maneuverability, allowing users to navigate tight spaces and tricky terrain with ease.

The snow thrower also features ergonomic handles with easy-grip controls, ensuring comfort during extended use. The built-in LED headlights enhance visibility in low-light conditions, allowing users to operate the machine safely during early morning or late evening snow removal.

Durability is a key characteristic of the Cub Cadet Two Stage Snow Thrower. Its solid construction, reinforced housing, and high-quality materials ensure that this equipment can withstand harsh winter conditions year after year. With comprehensive maintenance schedules and readily available customer support, owners can rest assured that their investment is protected.

In summary, the Cub Cadet Two Stage Snow Thrower combines power, innovation, and user-friendly features, making it a top choice for efficient snow removal. Its robust engine, two-stage system, and advanced technology make tackling winter weather more manageable than ever.
Top Page Image Contents