Cub Cadet Two Stage Snow Thrower warranty Friction Wheel Removal

Page 19

Figure 6-13

Figure 6-14

Figure 6-15

Friction Wheel Removal

If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust- ment on page 12 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary.

•Place the shift lever in third Forward (F3) position.

•Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

•Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

1.a. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Figure 6-13.

b.Remove the right-hand wheel by removing the screw and cupped washer which secure it to the axle.

2.Carefully remove the hex nut and washer which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame. See Figure 6-14.

3.Carefully position the hex shaft downward and to the left before carefully sliding the friction wheel assembly off the shaft. See Figure 6-15.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft. Follow the steps above in reverse order to reassemble components. If you’re disassem- bling the friction wheel and replacing only the rubber ring, proceed as follows:

4.Remove the four screws which secure the friction wheel’s side plates together. See Figure 6-16.

•Remove the rubber ring from between the plates.

•Reassemble the side plates with a new rubber ring.

•Slide the friction wheel assembly back onto the hex shaft and follow the steps above in reverse order to reassemble components.

Figure 6-16

6

Maintaining

Your Snow

Thrower

When reassembling the friction wheel as- sembly, tighten each screw only one rota- tion before turning the wheel clockwise and proceeding with the next screw. Repeat this process several times to ensure the plates are secured with equal force.

NEVER replace the auger shear pins with standard hex pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 06/06/07 Two-Stage Snow ThrowerOttawa Street South, KITCHENER, Ontario N2G 4J1 769-03263Finding and Recording Model Number Table of ContentsCustomer Support Your Responsibility Restrict the use Chute Clean-out ToolYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Shear Pin Storage optional Setting Up Your Snow ThrowerSnowthrower Model Drift Cutters If EquippedAll models Tire Pressure Pneumatic Tires Clean-Out ToolLamp Wiring Harness If equipped Skid ShoesKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpElectric Starter If Equipped Auger Control Test To Engage DriveTo Engage Augers Recoil StarterDrive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlReversible Steel Skid Shoe Reversible Plastic Skid ShoeShave Plate and Skid Shoes Maintaining Your Snow ThrowerEngine LubricationRoll the auger belt off the engine pulley. See Figure Auger Belt ReplacementUnhook the support bracket spring from the frame Remove and replace belt in the reverse order Drive Belt ReplacementRemove the rubber ring from between the plates Friction Wheel RemovalWipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting10.30.06 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Manual Chute Control Part Description RÉF Pièce Optional/en option Part Description RÉF Pièce Remarque Lhabitacle peut être légèrement différent 30 in/poPart Description RÉF Pièce 31AE6GKF500 Part For parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Page Commerciale Utilisation GarantieDépannage Solution Causes ProblèmeSouffleuse Propre etCarburant le Videz Gaz ’entretien Régime Transmission De courroie la de RemplacementTarières Régime ’entretienLubrification Patins et plate LameMoteur Plastique en réversible Patins 4-5 Figure Tarière la de CommandeRéglages PatinsVitesses de changement de Câble Et transmission la de CommandeGoulotte la de Commande Vitesses de levier150F dépasser SouffleuseMain ToucherCertains sur électrique Démarreur ’huile et d’essence PleinsModèles certains sur électrique Démarreur ModèlesSouffleuse la Trans de commande la de BlocageTarières La de proximité àDépart de Volet Souffleuse la de Commandes’essence plein le jamais faites Ne Goulotte la de dégagement de Outil Général d’ordre RecommandationsGoulotte la de dégagement de Outil Pneumatiques Bandages pneus des PressionÉchéant cas le coupe de Barres Option en cisaillement de goupille la de Remisage ’assemblage Après .ESSENCE Sans mais d’huile plein InférieurEmployer à moteur à l’huile à et carburant au Quant moteur du d’utilisation notice la consulter veuillezGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de DuréeResponsabilité Votre UtilisationPréparation FormationDe Outil Est goulotte la de dégagement de outil Un’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des Table4J1 N2G Ontario KITCHENER, South, Street Ottawa Phases deux neige à Souffleuse03263-769

Two Stage Snow Thrower specifications

The Cub Cadet Two Stage Snow Thrower is an exceptional piece of equipment designed to tackle the challenges of winter weather with efficiency and ease. This powerful snow removal machine is engineered to provide high-performance snow clearing, making it an essential tool for homeowners dealing with heavy snowfall.

One of the standout features of the Cub Cadet Two Stage Snow Thrower is its robust engine. Equipped with a reliable, heavy-duty engine, this snow thrower delivers exceptional torque and ensures seamless operation even under the most challenging conditions. The engine's efficiency contributes to its ability to clear snow quickly, making it ideal for large driveways and sidewalks.

The two-stage system is another hallmark of this machine. Utilizing an auger and impeller system, the snow thrower can efficiently gather and throw snow a considerable distance away, preventing snow from piling up in unwanted areas. This dual-action mechanism allows for faster clearing times and less manual labor, as it effectively handles both light flurries and heavy, wet snow.

Cub Cadet incorporates advanced technologies in their snow thrower designs. One notable feature is the push-button electric start, which eliminates the hassle of manual starting, especially in frigid temperatures. This convenience ensures that users can quickly power up the machine and begin their snow-clearing tasks without delay.

In terms of control, this model offers intuitive handling and customizable settings. The adjustable skid shoes allow users to modify the clearing height, ensuring effective operation on various surfaces, including driveways, sidewalks, and gravel. Additionally, the six-speed forward and two-speed reverse settings provide optimal maneuverability, allowing users to navigate tight spaces and tricky terrain with ease.

The snow thrower also features ergonomic handles with easy-grip controls, ensuring comfort during extended use. The built-in LED headlights enhance visibility in low-light conditions, allowing users to operate the machine safely during early morning or late evening snow removal.

Durability is a key characteristic of the Cub Cadet Two Stage Snow Thrower. Its solid construction, reinforced housing, and high-quality materials ensure that this equipment can withstand harsh winter conditions year after year. With comprehensive maintenance schedules and readily available customer support, owners can rest assured that their investment is protected.

In summary, the Cub Cadet Two Stage Snow Thrower combines power, innovation, and user-friendly features, making it a top choice for efficient snow removal. Its robust engine, two-stage system, and advanced technology make tackling winter weather more manageable than ever.
Top Page Image Contents