Cub Cadet SWE 528 warranty To Engage Drive, To Engage Augers, Auger Control Test

Page 11

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

3.To turn the unit left or right, squeeze the respective wheel steering control. See Figure 12.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Auger Control Test

Perform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

2.In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position.

3.While standing in the operator’s position (behind the snow thrower), engage the auger.

4.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

5.With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine.

6.Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

7.To readjust the control cable, loosen the upper hex nut on the auger cable bracket.

8.Position the bracket upward to provide more slack (or downward to increase cable tension). See Figure 13.

9.Retighten the upper hex nut.

10.Repeat Auger Control Test to verify proper adjustment has been achieved.

Figure 13

4

Operating

Your Snow

Thrower

WARNING

The muffler, engine and surrounding areas become hot and can cause a burn. Do not touch.

When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower.

NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system.

11

Image 11
Contents 06/02/2006 Two-Stage Snow Thrower Model SWEForm no -01791A Customer Support Table of ContentsFinding and Recording Model Number %, 352&!#%3 Chute clean-out tool is fastened to the topYour Responsibility 53% %842! #!54/ %. /0%2!4Your Responsibility Restrict the use PracticesYour Responsibility Do not modify engineTighten hand knobs securing upper handle to lower handle Setting Up Your Snow ThrowerTire Pressure Chute Clean-Out ToolShear Pin Storage Know Your Snow Thrower Operating Your Snow ThrowerYour Snow Thrower OperatingElectric Starter Gas & Oil Fill-UpStopping The Engine Starting The EngineAuger Control Test To Engage DriveTo Engage Augers Drive Control Shift Lever Making AdjustmentsShift Cable Chute ControlAuger Control Skid ShoesLubrication Maintaining Your Snow ThrowerGeneral Recommendations EngineReplacing Shave Plate Shave Plate and Skid ShoesReplacing Belt Replacing Skid ShoeRoll auger belt off the pulley as shown in Figure Auger BeltWheel and friction wheel disc. See Figure Drive BeltFriction Wheel Rubber Short-Term Storage Off-Season StoragePreparing Engine Preparing Snow ThrowerTrouble- shooting This section Addresses minor Service issuesPage Parts, call the Customer Dealer Referral Line at Parts ListTo order replacement Or visit    Shoulder Nut, 1/4-20 738-04194 Flange Shoulder ScrewLock Plate Clutch Lock Cam55 56 790-00226 Frame Cover Friction Wheel Disc AssemblyAB Screw, 1/4-20 x 790-00096 Auger Cable Guide Bracket 748-0190 SpacerPage Contact MTD Products Limited, Kitchener, on N2G 4J1, or call U.S.A CanadaMANUFACTURER’S Limited Warranty for

SWE 528 specifications

The Cub Cadet SWE 528 is a powerful and versatile snow blower designed for homeowners who demand efficiency and reliability during winter months. This model is notable for its robust performance and innovative features that make snow removal an easier and more streamlined task.

One of the standout characteristics of the SWE 528 is its 28-inch clearing width, allowing users to clear large areas of snow in a single pass. The machine is powered by a dependable 420cc OHV engine, delivering ample power and torque to tackle even the most stubborn snow. The engine's design ensures smooth operation, providing the strength needed to clear heavy, wet snow and dealing effortlessly with snowdrifts.

The SWE 528 features a heavy-duty steel auger that efficiently breaks up and gathers snow, sending it through an impressive 200-degree adjustable chute. This pivotal chute design allows for precise control over the direction of snow disbursement, giving users the ability to decide where to send the snow, whether it's onto a driveway, yard, or away from pathways.

Another notable technology in the SWE 528 is its electric start function, which provides a hassle-free way to fire up the engine regardless of the cold weather conditions. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms in frigid temperatures. Moreover, the model includes a reliable 6-speed transmission that features both forward and reverse settings, allowing for greater mobility and control when navigating various terrains and snow depths.

Comfort is also a key focus in the design of the Cub Cadet SWE 528. It comes equipped with ergonomically designed handles, which provide a comfortable grip and reduce user fatigue during extended use. Additionally, the heated hand grips keep hands warm while operating the snow blower in the coldest conditions, making it an excellent choice for winter storms.

The SWE 528 is built to withstand the elements with its durable construction, featuring a rust-resistant finish and high-impact components that are made to endure harsh winter conditions. Overall, the Cub Cadet SWE 528 combines power, convenience, and durability, making it an excellent investment for anyone looking to simplify their winter snow management tasks. Its impressive features and user-friendly design set it apart in the competitive snow blower market, delivering performance that meets the needs of homeowners in snowy climates.