Cub Cadet SWE 528 warranty Setting Up Your Snow Thrower

Page 6

3

Setting Up

Your Snow

Thrower

All references in this manual to the left or right side of the snow thrower is from the operating position only. Exceptions, if any, will be specified.

IMPORTANT: This unit is shipped with the engine full of oil. After assembly, refer to the Tecumseh Engine manual packed separately with your snow thrower for fuel and oil fill-up details.

This Operator’s Manual may cover a range of product specifications for various models. Char- acteristics and features discussed and/or illustrated in this manual may not be applicable to all models.

!

"

Figure 1

Figure 2

Figure 3

This Operator’s Manual may cover a range of product specifications. Characteristics and features discussed and/or illustrated in this manual may not be applicable to all models.

IMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel). Refer to “Augers” section in the Maintenance section for more information regarding shear pin replace- ment.

1.Remove the unit from the crate or carton.

2.Observe the lower area of the snow thrower to be sure both cables are aligned with roller guides before pivoting handle upward.

a.Pull up and back on upper handle as shown in Figure 1. Align upper handle with the lower handle.

b.Tighten hand knobs securing upper handle to lower handle.

3.Certain units may require assembly of the chute. If this is the case, follow steps 4-7 to install the chute. If the chute on the unit is attached, proceed to step 8.

4.Remove wing nut and hex screw from chute control assembly and clevis pin and cotter pin from chute support bracket. See Figure 2. Position the chute assembly (forward-facing) over the chute base.

5.Place the 4-way chute control in a centered position. See Figure 3.

6.Place chute assembly onto chute base and secure chute control assembly to chute support bracket with clevis pin and cotter pin removed earlier. See Figure 4.

7.Finish securing chute control assembly to chute support bracket with wing nut and hex screw removed earlier. See Figure 5.

8.Check that all cables are properly routed through the cable guide on top of the engine. See Figure 6.

9.The extension cord is fastened with a cable tie to the rear of the auger housing for shipping purposes. Cut the cable tie and remove it before operating the unit.

Figure 4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Two-Stage Snow Thrower Model SWE Form no -01791A06/02/2006 Table of Contents Finding and Recording Model NumberCustomer Support 53% %842! #!54/ %. /0%2!4 Chute clean-out tool is fastened to the topYour Responsibility %, 352&!#%3Practices Your Responsibility Restrict the useDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Tighten hand knobs securing upper handle to lower handleChute Clean-Out Tool Shear Pin StorageTire Pressure Operating Your Snow Thrower Know Your Snow ThrowerOperating Your Snow ThrowerStarting The Engine Gas & Oil Fill-UpStopping The Engine Electric StarterTo Engage Drive To Engage AugersAuger Control Test Chute Control Making AdjustmentsShift Cable Drive Control Shift LeverSkid Shoes Auger ControlEngine Maintaining Your Snow ThrowerGeneral Recommendations LubricationReplacing Skid Shoe Shave Plate and Skid ShoesReplacing Belt Replacing Shave PlateAuger Belt Roll auger belt off the pulley as shown in FigureDrive Belt Friction Wheel RubberWheel and friction wheel disc. See Figure Preparing Snow Thrower Off-Season StoragePreparing Engine Short-Term StorageThis section Addresses minor Service issues Trouble- shootingPage Or visit Parts ListTo order replacement Parts, call the Customer Dealer Referral Line at    Clutch Lock Cam 738-04194 Flange Shoulder ScrewLock Plate Shoulder Nut, 1/4-2055 56 790-00096 Auger Cable Guide Bracket 748-0190 Spacer Friction Wheel Disc AssemblyAB Screw, 1/4-20 x 790-00226 Frame CoverPage U.S.A Canada Contact MTD Products Limited, Kitchener, on N2G 4J1, or callMANUFACTURER’S Limited Warranty for

SWE 528 specifications

The Cub Cadet SWE 528 is a powerful and versatile snow blower designed for homeowners who demand efficiency and reliability during winter months. This model is notable for its robust performance and innovative features that make snow removal an easier and more streamlined task.

One of the standout characteristics of the SWE 528 is its 28-inch clearing width, allowing users to clear large areas of snow in a single pass. The machine is powered by a dependable 420cc OHV engine, delivering ample power and torque to tackle even the most stubborn snow. The engine's design ensures smooth operation, providing the strength needed to clear heavy, wet snow and dealing effortlessly with snowdrifts.

The SWE 528 features a heavy-duty steel auger that efficiently breaks up and gathers snow, sending it through an impressive 200-degree adjustable chute. This pivotal chute design allows for precise control over the direction of snow disbursement, giving users the ability to decide where to send the snow, whether it's onto a driveway, yard, or away from pathways.

Another notable technology in the SWE 528 is its electric start function, which provides a hassle-free way to fire up the engine regardless of the cold weather conditions. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms in frigid temperatures. Moreover, the model includes a reliable 6-speed transmission that features both forward and reverse settings, allowing for greater mobility and control when navigating various terrains and snow depths.

Comfort is also a key focus in the design of the Cub Cadet SWE 528. It comes equipped with ergonomically designed handles, which provide a comfortable grip and reduce user fatigue during extended use. Additionally, the heated hand grips keep hands warm while operating the snow blower in the coldest conditions, making it an excellent choice for winter storms.

The SWE 528 is built to withstand the elements with its durable construction, featuring a rust-resistant finish and high-impact components that are made to endure harsh winter conditions. Overall, the Cub Cadet SWE 528 combines power, convenience, and durability, making it an excellent investment for anyone looking to simplify their winter snow management tasks. Its impressive features and user-friendly design set it apart in the competitive snow blower market, delivering performance that meets the needs of homeowners in snowy climates.
Top Page Image Contents