Cub Cadet SWE 528 warranty Shear Pin Storage, Chute Clean-Out Tool, Tire Pressure

Page 7

CAUTION: Prior to operating your snow thrower, refer to Auger Control Test in Operation section. Read and follow all instructions carefully, and

perform all adjustments to verify your snow thrower is operating safely and properly.

Shear Pin Storage

Holes are located in the plastic dash panel for convenient shear pin storage. See Figure 7.

IMPORTANT: This unit is shipped with the engine full of oil. After assembly, refer to engine manual for fuel and oil fill-up details.

Chute Clean-Out Tool

3

Setting Up

Your Snow

Thrower

The clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. See Figure 8.

1.Release both the auger control and the drive/auger control lock.

2.Stop the engine by moving the throttle to the stop position.

3.Remove the clean-out tool from the mounting clip.

4.Use the shovel-shaped end of the clean-out tool to remove any snow and ice in the chute assembly.

5.Re-fasten the clean-out tool to the mounting clip on the rear of the auger housing and restart engine.

6.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow or ice from the chute assembly before continuing to clear snow.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing.

Tire Pressure

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary. NOTE: If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

Under any circumstance do not exceed manufactur- er’s recommended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.

Figure 5

Figure 6

Figure 7

#HUTEU#LEANOUTL4OOL

Figure 8

WARNING

Prior to operating your snow thrower, refer to Auger Control Test in Operation section. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Never use your hands to clean snow and ice from the chute assembly or auger housing.

IMPORTANT: Under any circumstance do not exceed manufacturer’s recommended psi. Equal tire pressure should be maintained at all times. Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury. Refer to sidewall of tire for recommended pressure.



Page 6 Page 8
Image 7
Page 6 Page 8
Contents Form no -01791A Two-Stage Snow Thrower Model SWE06/02/2006 Finding and Recording Model Number Table of ContentsCustomer Support %, 352&!#%3 Chute clean-out tool is fastened to the topYour Responsibility 53% %842! #!54/ %. /0%2!4Your Responsibility Restrict the use PracticesYour Responsibility Do not modify engineTighten hand knobs securing upper handle to lower handle Setting Up Your Snow ThrowerShear Pin Storage Chute Clean-Out ToolTire Pressure Know Your Snow Thrower Operating Your Snow ThrowerYour Snow Thrower OperatingElectric Starter Gas & Oil Fill-UpStopping The Engine Starting The EngineTo Engage Augers To Engage DriveAuger Control Test Drive Control Shift Lever Making AdjustmentsShift Cable Chute ControlAuger Control Skid ShoesLubrication Maintaining Your Snow ThrowerGeneral Recommendations EngineReplacing Shave Plate Shave Plate and Skid ShoesReplacing Belt Replacing Skid ShoeRoll auger belt off the pulley as shown in Figure Auger BeltFriction Wheel Rubber Drive BeltWheel and friction wheel disc. See Figure Short-Term Storage Off-Season StoragePreparing Engine Preparing Snow ThrowerTrouble- shooting This section Addresses minor Service issuesPage Parts, call the Customer Dealer Referral Line at Parts ListTo order replacement Or visit    Shoulder Nut, 1/4-20 738-04194 Flange Shoulder ScrewLock Plate Clutch Lock Cam55 56 790-00226 Frame Cover Friction Wheel Disc AssemblyAB Screw, 1/4-20 x 790-00096 Auger Cable Guide Bracket 748-0190 SpacerPage Contact MTD Products Limited, Kitchener, on N2G 4J1, or call U.S.A CanadaMANUFACTURER’S Limited Warranty for

SWE 528 specifications

The Cub Cadet SWE 528 is a powerful and versatile snow blower designed for homeowners who demand efficiency and reliability during winter months. This model is notable for its robust performance and innovative features that make snow removal an easier and more streamlined task.

One of the standout characteristics of the SWE 528 is its 28-inch clearing width, allowing users to clear large areas of snow in a single pass. The machine is powered by a dependable 420cc OHV engine, delivering ample power and torque to tackle even the most stubborn snow. The engine's design ensures smooth operation, providing the strength needed to clear heavy, wet snow and dealing effortlessly with snowdrifts.

The SWE 528 features a heavy-duty steel auger that efficiently breaks up and gathers snow, sending it through an impressive 200-degree adjustable chute. This pivotal chute design allows for precise control over the direction of snow disbursement, giving users the ability to decide where to send the snow, whether it's onto a driveway, yard, or away from pathways.

Another notable technology in the SWE 528 is its electric start function, which provides a hassle-free way to fire up the engine regardless of the cold weather conditions. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms in frigid temperatures. Moreover, the model includes a reliable 6-speed transmission that features both forward and reverse settings, allowing for greater mobility and control when navigating various terrains and snow depths.

Comfort is also a key focus in the design of the Cub Cadet SWE 528. It comes equipped with ergonomically designed handles, which provide a comfortable grip and reduce user fatigue during extended use. Additionally, the heated hand grips keep hands warm while operating the snow blower in the coldest conditions, making it an excellent choice for winter storms.

The SWE 528 is built to withstand the elements with its durable construction, featuring a rust-resistant finish and high-impact components that are made to endure harsh winter conditions. Overall, the Cub Cadet SWE 528 combines power, convenience, and durability, making it an excellent investment for anyone looking to simplify their winter snow management tasks. Its impressive features and user-friendly design set it apart in the competitive snow blower market, delivering performance that meets the needs of homeowners in snowy climates.
Top Page Image Contents