Cub Cadet SWE 528 Off-Season Storage, Preparing Engine, Preparing Snow Thrower, Long-Term Storage

Page 18

7

If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last pos- sibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years.

Off-Season

Storage

WARNING

Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or

gas appliance.

Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

Never use engine or carbu- retor cleaning products in the fuel tank or permanent damage may occur.

Preparing Engine

NOTE: Refer to the engine manual for more detailed information on preparing the snow thrower engine for storage.

Short-Term Storage

It is important to prevent gum deposits from forming in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose, or tank during short-term storage (15-30 days). To prevent this, treat the fuel system using a fuel stabalizer.

Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™) is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow it to reach the carburetor.

WARNING: Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot

light as on a furnace, water heater, clothes dryer or gas appliance.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of

acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Long-Term Storage

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer.

WARNING: Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

1.Run the engine until the fuel tank is empty and it stops due to lack of fuel. Do not attempt to pour fuel from the engine.

WARNING: Never use engine or carbu- retor cleaning products in the fuel tank or permanent damage may occur.

2.Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Cover spark plug hole with a rag and crank the engine several times to distribute the oil. Replace spark plug.

Preparing Snow Thrower

When storing the snow thrower in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

Remove all dirt from exterior of engine and equipment.

Follow lubrication recommendations.

Store equipment in a clean, dry area.

18

Image 18
Contents Two-Stage Snow Thrower Model SWE Form no -01791A06/02/2006 Table of Contents Finding and Recording Model NumberCustomer Support 53% %842! #!54/ %. /0%2!4 Chute clean-out tool is fastened to the topYour Responsibility %, 352&!#%3Practices Your Responsibility Restrict the useDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Tighten hand knobs securing upper handle to lower handleChute Clean-Out Tool Shear Pin StorageTire Pressure Operating Your Snow Thrower Know Your Snow ThrowerOperating Your Snow ThrowerStarting The Engine Gas & Oil Fill-UpStopping The Engine Electric StarterTo Engage Drive To Engage AugersAuger Control Test Chute Control Making AdjustmentsShift Cable Drive Control Shift LeverSkid Shoes Auger ControlEngine Maintaining Your Snow ThrowerGeneral Recommendations LubricationReplacing Skid Shoe Shave Plate and Skid ShoesReplacing Belt Replacing Shave PlateAuger Belt Roll auger belt off the pulley as shown in FigureDrive Belt Friction Wheel RubberWheel and friction wheel disc. See Figure Preparing Snow Thrower Off-Season StoragePreparing Engine Short-Term StorageThis section Addresses minor Service issues Trouble- shootingPage Or visit Parts ListTo order replacement Parts, call the Customer Dealer Referral Line at    Clutch Lock Cam 738-04194 Flange Shoulder ScrewLock Plate Shoulder Nut, 1/4-2055 56 790-00096 Auger Cable Guide Bracket 748-0190 Spacer Friction Wheel Disc AssemblyAB Screw, 1/4-20 x 790-00226 Frame CoverPage U.S.A Canada Contact MTD Products Limited, Kitchener, on N2G 4J1, or callMANUFACTURER’S Limited Warranty for

SWE 528 specifications

The Cub Cadet SWE 528 is a powerful and versatile snow blower designed for homeowners who demand efficiency and reliability during winter months. This model is notable for its robust performance and innovative features that make snow removal an easier and more streamlined task.

One of the standout characteristics of the SWE 528 is its 28-inch clearing width, allowing users to clear large areas of snow in a single pass. The machine is powered by a dependable 420cc OHV engine, delivering ample power and torque to tackle even the most stubborn snow. The engine's design ensures smooth operation, providing the strength needed to clear heavy, wet snow and dealing effortlessly with snowdrifts.

The SWE 528 features a heavy-duty steel auger that efficiently breaks up and gathers snow, sending it through an impressive 200-degree adjustable chute. This pivotal chute design allows for precise control over the direction of snow disbursement, giving users the ability to decide where to send the snow, whether it's onto a driveway, yard, or away from pathways.

Another notable technology in the SWE 528 is its electric start function, which provides a hassle-free way to fire up the engine regardless of the cold weather conditions. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms in frigid temperatures. Moreover, the model includes a reliable 6-speed transmission that features both forward and reverse settings, allowing for greater mobility and control when navigating various terrains and snow depths.

Comfort is also a key focus in the design of the Cub Cadet SWE 528. It comes equipped with ergonomically designed handles, which provide a comfortable grip and reduce user fatigue during extended use. Additionally, the heated hand grips keep hands warm while operating the snow blower in the coldest conditions, making it an excellent choice for winter storms.

The SWE 528 is built to withstand the elements with its durable construction, featuring a rust-resistant finish and high-impact components that are made to endure harsh winter conditions. Overall, the Cub Cadet SWE 528 combines power, convenience, and durability, making it an excellent investment for anyone looking to simplify their winter snow management tasks. Its impressive features and user-friendly design set it apart in the competitive snow blower market, delivering performance that meets the needs of homeowners in snowy climates.