Cub Cadet 769-03268 Drive Control / Auger Control Lock, Two-Way Chute Control, Ignition Key

Page 11

Auger Control

The auger control is located on the left handle. Squeeze the auger control to engage the augers. Release to stop the snow throwing action. The drive control must also be released in order to stop auger.

Drive Control / Auger Control Lock

The drive control is located on the right handle. Squeeze the drive control to engage the wheel drive. Release to stop.

This same lever also locks the auger control so you can operate the chute crank without interrupting the snow throwing process. If the auger control is engaged simultaneously with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release the drive control to stop the augers and wheel drive (the auger control must also be released).

IMPORTANT: Always release the drive control before changing speeds.

Two-Way Chute Control™)

This two-way control lever is meant to control the distance of snow discharge from the chute. Tilt the lever forward or rearward to adjust the distance snow will be thrown.

Ignition Key

The ignition key must be inserted and snapped in place in order for the engine to start. Remove the ignition key to prevent unauthorized use of equipment. Do NOT attempt to turn the key.

Chute Clean-Out Tool

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

The clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip.

1.Release both the auger control and the drive/auger control lock.

2.Stop the engine by moving the throttle to the stop position.

3.Remove the clean-out tool from the mounting clip.

4.Use the shovel-shaped end of the clean-out tool to remove any snow and ice in the chute assembly.

5.Re-fasten the clean-out tool to the mounting clip on the rear of the auger housing and restart engine.

6.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow or ice from the chute assembly before continuing to clear snow.

Skid Shoes

4

Operating

Your Snow

Thrower

WARNING

The operation of any snow thrower can result in foreign objects being thrown into the eyes, which

Chute Directional Control

The chute directional control is located on left side of the snow thrower.

To change the direction in which snow is thrown, turn chute direc- tional control as follows:

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

CLOCKWISE TO DISCHARGE LEFT

COUNTER CLOCKWISE TO DISCHARGE RIGHT

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Headlight

The headlight is on whenever the engine is running.

can damage your eyes severely. Always wear safety glasses while operating the snow thrower, or while performing any adjust- ments or repairs on it.

Be sure no one other than the operator is standing near the snow thrower while starting engine or operating

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles. Squeeze the right control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you are familiar with these controls.

snow thrower. Never run engine indoors or in enclosed, poorly ventilated areas. En- gine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts on engine and snow thrower.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 07/10/07 Two-Stage Snow ThrowerOttawa Street South, KITCHENER, Ontario N2G 4J1 769-03268Customer Support Table of ContentsFinding and Recording Model Number Your Responsibility Restrict the use Chute Clean-out ToolResult in personal injury. When you see this symbol, Heed Allow machine to cool at least 5 minutes before storing Safe Operation PracticesYour Responsibility Safe Handling of GasolineAverage Useful Life Do not modify engineSetting Up Your Snow Thrower Attaching the Shift Rod Attaching the Chute AssemblyDrift Cutters If Equipped Clean-Out ToolFinal Adjustments Auger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow ThrowerIgnition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlElectric Starter on certain models Recoil StarterStopping The Engine Starting The EngineOperating Tips Always observe safety rules when performing any maintenanceTo Engage Drive To Engage AugersDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerAuger Belt Replacing BeltsApply Loctite 262 to the threads of the hex screw used Drive BeltWasher. Torque hex screw 250-325 in. lbs Steps in the opposite order and manner of removalFriction Wheel Friction wheel assembly and hold assembly in positionChanging Friction Wheel Rubber Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting10.30.06 WarrantyFor parts and/or accessories refer to customer support on 6919 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesAdressez-vous au «Service après-vente» Asphalt. Set to Torque to 20-30 in./lbsSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Ground Plug into alternator Lead wire under fuel tankGround wire to engine Ground wire to engineTec Tec. LH 358 ccPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page 06.30.10 GarantiePas Solution Causes ProblèmeDépannage Place en bougie Propre etSouffleuse Carburant le Videz Gaz’essieu de Frottement de roue caoutchoucEn bague la de Changement Frottement de RoueAdaptateur Vis la enlever pour po 1/2 de clé une Utilisez .aBoulon l’autre retirez Courroies les de RemplacementÉloignez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentLa de support du Ajustement Tarière la de CommandeRéglages GoulotteRoues Des l’entraînement de CommandeVitesses de levier du Tige ’utilisation Conseils Général d’ordre RecommandationsCertains sur électrique Démarreur Moteur du ArrêtAnt ModèlesPatins ’orientation CommandeGoulotte la de direction de Commande PhareDépart de Volet Souffleuse la de Commandes’obturateur de Commande Amorçeur’ajustement Vérifiez TiquesPneuma Bandages pneus des Pression Main Réglages DerniersBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation Cette Remarque Les RemarqueMatériels Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisSeulement Responsabilité Votre’essence de Manipulation Dégagement Est goulotte la de dégagement de outil UnDe Outil Goulotte la edMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour03268-769 Phases deux neige à Souffleuse07/09/07 4J1 N2G Ontario KITCHENER, South, Street Ottawa
Top Page Image Contents