Cub Cadet 769-03268 Making, Adjustments, Shift Rod, Drive Control, Reassemble the frame cover

Page 14

5

Making

Adjustments

WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Never attempt to make any adjust- ments while the engine is running, except where speci- fied in operator’s manual.

Figure 15

Shift Rod

If the full range of speeds (forward and reverse) cannot be achieved, refer to Figure 15 and adjust the shift rod as follows:

1.Looking underneath the handle panel, note which of the three holes in the shift lever the ferrule is inserted into. Also note the direction of insertion. Then remove the internal cotter pin and flat washer from the ferrule and withdraw the ferrule from the shift lever. See Figure 15.

2.Place shift lever in sixth (6) position or fastest forward speed.

3.Push shift rod and shift arm assembly down sharply, as far as it will go to put the drive into the fastest forward position.

4.As necessary, rotate the ferrule up or down the shift rod until the ferrule lines up with the hole from which it was earlier removed. See Figure 15.

5.From the direction noted earlier, insert the ferrule into the proper hole.

6.Reinstall the washer and the internal cotter pin.

Drive Control

Refer to the Final Adjustment section of the Set-Up instructions to adjust the drive control. To further check the adjustment, proceed as follows:

1.Drain the gasoline out of your snow thrower’s engine, and place a piece of plastic film under the gas cap to avoid spillage.

2.Tip the snow thrower forward, allowing it to rest on the auger housing.

3.Remove the frame cover underneath the snow thrower by removing the self-tapping screws. See Figure 16.

4.With the wheel drive control released, check if there is clearance between friction wheel and drive plate in all positions of the shift lever. See Figure 17.

Figure 16

Friction

Wheel

Drive	Axle Supp.
Plate	Brkt.
	Opening

Figure 17

5.With the drive control lever engaged, check if the friction wheel solidly contacts the drive plate. See Figure 17. If not, adjust as follows:

a.Loosen the jam nut on the traction drive cable and thread the cable in or out as necessary.

b.Retighten the jam nut to secure the cable when correct adjustment is reached.

6.Reassemble the frame cover.

NOTE: If you placed plastic film under the gas cap earlier, remove it now.

14

Image 14

Contents 769-03268 Two-Stage Snow ThrowerOttawa Street South, KITCHENER, Ontario N2G 4J1 07/10/07Customer Support Table of ContentsFinding and Recording Model Number Your Responsibility Restrict the use Chute Clean-out ToolResult in personal injury. When you see this symbol, Heed Safe Handling of Gasoline Safe Operation PracticesYour Responsibility Allow machine to cool at least 5 minutes before storingDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Attaching the Chute Assembly Attaching the Shift RodDrift Cutters If Equipped Clean-Out ToolFinal Adjustments Tire Pressure Pneumatic Tires Check the adjustment of the auger control as followsSkid Shoes AugerOperating Your Snow Thrower Know Your Snow ThrowerTwo-Way Chute Control Chute Clean-Out ToolDrive Control / Auger Control Lock Ignition KeyStarting The Engine Recoil StarterStopping The Engine Electric Starter on certain modelsTo Engage Augers Always observe safety rules when performing any maintenanceTo Engage Drive Operating TipsShift Rod AdjustmentsMaking Drive ControlSee Figure Adjust skid shoes as follows Chute AssemblyChute Bracket Adjustment Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger BeltSteps in the opposite order and manner of removal Drive BeltWasher. Torque hex screw 250-325 in. lbs Apply Loctite 262 to the threads of the hex screw usedFriction Wheel Friction wheel assembly and hold assembly in positionChanging Friction Wheel Rubber Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 10.30.06For parts and/or accessories refer to customer support on 6919 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesAdressez-vous au «Service après-vente» Torque to 20-30 in./lbs Asphalt. Set toSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Ground wire to engine Plug into alternator Lead wire under fuel tankGround wire to engine GroundTec. LH 358 cc TecPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Garantie 06.30.10Pas Solution Causes ProblèmeDépannage Carburant le Videz Gaz Propre etSouffleuse Place en bougieFrottement de Roue Frottement de roue caoutchoucEn bague la de Changement ’essieu deVis la enlever pour po 1/2 de clé une Utilisez .a AdaptateurTarière la de d’entraînement Courroie Courroies les de RemplacementÉloignez Boulon l’autre retirezVitesse de ment LubrificationRoues ’engrenageGoulotte Tarière la de CommandeRéglages La de support du AjustementRoues Des l’entraînement de CommandeVitesses de levier du Tige Général d’ordre Recommandations ’utilisation ConseilsModèles Moteur du ArrêtAnt Certains sur électrique DémarreurPhare ’orientation CommandeGoulotte la de direction de Commande PatinsAmorçeur Souffleuse la de Commandes’obturateur de Commande Départ de Volet’ajustement Vérifiez TiquesPneuma Bandages pneus des Pression Réglages Derniers MainBien passe qu’il ce jusqu’à raccord le sur Tapez Vitesses de levier du tige la de InstallationGoulotte la de Installation Les Remarque Cette RemarqueGaz de émissions les concernant Avis Responsabilité VotreMoyenne utile vie de Durée MatérielsSeulement Responsabilité Votre’essence de Manipulation Goulotte la ed Est goulotte la de dégagement de outil UnDe Outil DégagementModèle de numéro le trouver Pour Vente-après ServiceVente-après service au d’abord adresser vous sans Matières des Table4J1 N2G Ontario KITCHENER, South, Street Ottawa Phases deux neige à Souffleuse07/09/07 03268-769