Cub Cadet 769-03268 warranty Chute Clean-out Tool, Your Responsibility Restrict the use

Page 3

1

Safety Labels

#3

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may

Chute Clean-out

Tool

Achute clean-out tool is fastened to the top of the auger housing with a mounting clip. The tool is designed to clear a chute assembly of ice and snow.

This item is fastened with a cable tie at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before using the clean-out tool to clear the chute assembly.

result in personal injury. When you see this symbol, HEED

ITS WARNING!

Your Responsibility Restrict the use

of this power machine to persons who read, understand

and follow the warnings and instructions

in this manual

and on the machine.

Image 3

Contents 07/10/07 Two-Stage Snow ThrowerOttawa Street South, KITCHENER, Ontario N2G 4J1 769-03268Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Result in personal injury. When you see this symbol, HeedYour Responsibility Restrict the use Allow machine to cool at least 5 minutes before storing Safe Operation PracticesYour Responsibility Safe Handling of GasolineAverage Useful Life Do not modify engineSetting Up Your Snow Thrower Attaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Auger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow ThrowerIgnition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlElectric Starter on certain models Recoil StarterStopping The Engine Starting The EngineOperating Tips Always observe safety rules when performing any maintenanceTo Engage Drive To Engage AugersDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerAuger Belt Replacing BeltsApply Loctite 262 to the threads of the hex screw used Drive BeltWasher. Torque hex screw 250-325 in. lbs Steps in the opposite order and manner of removalFriction wheel assembly and hold assembly in position Changing Friction Wheel RubberFriction Wheel Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting10.30.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Asphalt. Set to Torque to 20-30 in./lbsSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Ground Plug into alternator Lead wire under fuel tankGround wire to engine Ground wire to engineTec Tec. LH 358 ccPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page 06.30.10 GarantieSolution Causes Problème DépannagePas Place en bougie Propre etSouffleuse Carburant le Videz Gaz’essieu de Frottement de roue caoutchoucEn bague la de Changement Frottement de RoueAdaptateur Vis la enlever pour po 1/2 de clé une Utilisez .aBoulon l’autre retirez Courroies les de RemplacementÉloignez Tarière la de d’entraînement Courroie’engrenage LubrificationRoues Vitesse de mentLa de support du Ajustement Tarière la de CommandeRéglages GoulotteDes l’entraînement de Commande Vitesses de levier du TigeRoues ’utilisation Conseils Général d’ordre RecommandationsCertains sur électrique Démarreur Moteur du ArrêtAnt ModèlesPatins ’orientation CommandeGoulotte la de direction de Commande PhareDépart de Volet Souffleuse la de Commandes’obturateur de Commande AmorçeurTiques Pneuma Bandages pneus des Pression’ajustement Vérifiez Main Réglages DerniersVitesses de levier du tige la de Installation Goulotte la de InstallationBien passe qu’il ce jusqu’à raccord le sur Tapez Cette Remarque Les RemarqueMatériels Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisResponsabilité Votre ’essence de ManipulationSeulement Dégagement Est goulotte la de dégagement de outil UnDe Outil Goulotte la edMatières des Table Vente-après ServiceVente-après service au d’abord adresser vous sans Modèle de numéro le trouver Pour03268-769 Phases deux neige à Souffleuse07/09/07 4J1 N2G Ontario KITCHENER, South, Street Ottawa