Cub Cadet 769-03268 warranty Drive Belt, Washer. Torque hex screw 250-325 in. lbs

Page 18

6

Maintaining

Your Snow

Thrower

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

		Figure 29
Figure 28			Adapter
9. a. Using a 1/2” wrench, remove the hex screw and		b	Adapter
9. a. Using a 1/2” wrench, remove the hex screw and		b
washer from the center of the pulley on the auger
housing. See Figure 30.
b. Lift the brake bracket assembly out of the pulley
groove
c. Remove the pulley.
10. Remove and replace auger belt inside belt keepers.
11. Apply Loctite 262 to the threads of the hex screw used
for mounting the auger pulley.
12. Reassemble pulley to auger housing aligning pulley		c
slots with posts on adapter, secure with hex screw and		c
washer. Torque hex screw 250-325 in. lbs.	a	Slots
NOTE: Make sure the brake puck is seated in the pulley	a
NOTE: Make sure the brake puck is seated in the pulley
groove.		Figure 30
If also replacing the drive belt, proceed to the “Drive Belt”
instruction. If not, reassemble by performing the previous	1	3
steps in the opposite order and manner of removal.	1	3
steps in the opposite order and manner of removal.

Proper Adjustment: With the auger clutch lever in the disengaged position, the top surface of the new belt should be even with the outside diameter of the pulley.

1. To adjust, disconnect ferrule from brake bracket as- sembly and thread ferrule in (towards idler) to increase tension on belt, and out to decrease tension.

IMPORTANT

Refer to the Final Adjustment section of the Set-Up instructions after replacing drive

NOTE: The brake puck must always be firmly seated in the pulley groove when auger control is disengaged.

IMPORTANT: Repeat the “Auger Drive Control Test” from the Assembly section before operating snow thrower.

2

and auger belts.

Drive Belt

1.Pull the idler pulley away from the backside of the drive belt to relieve the tension and slide the drive belt off the idler pulley. See Figure 31.

2.Remove the belt from the bottom drive pulley and the engine pulley.

Figure 31

3.Install the new belt on the pulleys in the reverse order and re-tension with the idler pulley.

Reassemble your unit by performing the previous steps in the opposite order.

18

Image 18

Contents 769-03268 Two-Stage Snow ThrowerOttawa Street South, KITCHENER, Ontario N2G 4J1 07/10/07Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Result in personal injury. When you see this symbol, HeedYour Responsibility Restrict the use Safe Handling of Gasoline Safe Operation PracticesYour Responsibility Allow machine to cool at least 5 minutes before storingDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Attaching the Chute Assembly Attaching the Shift RodClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Tire Pressure Pneumatic Tires Check the adjustment of the auger control as followsSkid Shoes AugerOperating Your Snow Thrower Know Your Snow ThrowerTwo-Way Chute Control Chute Clean-Out ToolDrive Control / Auger Control Lock Ignition KeyStarting The Engine Recoil StarterStopping The Engine Electric Starter on certain modelsTo Engage Augers Always observe safety rules when performing any maintenanceTo Engage Drive Operating TipsShift Rod AdjustmentsMaking Drive ControlSee Figure Adjust skid shoes as follows Chute AssemblyChute Bracket Adjustment Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger BeltSteps in the opposite order and manner of removal Drive BeltWasher. Torque hex screw 250-325 in. lbs Apply Loctite 262 to the threads of the hex screw usedFriction wheel assembly and hold assembly in position Changing Friction Wheel RubberFriction Wheel Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 10.30.06For parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 20-30 in./lbs Asphalt. Set toSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Ground wire to engine Plug into alternator Lead wire under fuel tankGround wire to engine GroundTec. LH 358 cc TecPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Garantie 06.30.10Solution Causes Problème DépannagePas Carburant le Videz Gaz Propre etSouffleuse Place en bougieFrottement de Roue Frottement de roue caoutchoucEn bague la de Changement ’essieu deVis la enlever pour po 1/2 de clé une Utilisez .a AdaptateurTarière la de d’entraînement Courroie Courroies les de RemplacementÉloignez Boulon l’autre retirezVitesse de ment LubrificationRoues ’engrenageGoulotte Tarière la de CommandeRéglages La de support du AjustementDes l’entraînement de Commande Vitesses de levier du TigeRoues Général d’ordre Recommandations ’utilisation ConseilsModèles Moteur du ArrêtAnt Certains sur électrique DémarreurPhare ’orientation CommandeGoulotte la de direction de Commande PatinsAmorçeur Souffleuse la de Commandes’obturateur de Commande Départ de VoletTiques Pneuma Bandages pneus des Pression’ajustement Vérifiez Réglages Derniers MainVitesses de levier du tige la de Installation Goulotte la de InstallationBien passe qu’il ce jusqu’à raccord le sur Tapez Les Remarque Cette RemarqueGaz de émissions les concernant Avis Responsabilité VotreMoyenne utile vie de Durée MatérielsResponsabilité Votre ’essence de ManipulationSeulement Goulotte la ed Est goulotte la de dégagement de outil UnDe Outil DégagementModèle de numéro le trouver Pour Vente-après ServiceVente-après service au d’abord adresser vous sans Matières des Table4J1 N2G Ontario KITCHENER, South, Street Ottawa Phases deux neige à Souffleuse07/09/07 03268-769