Husqvarna 1330SB-XLSB owner manual Auger Assembly 30 LH, Auger Assembly 30 RH

Page 22

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 42 17-13 AUGER HOUSING
	2	532 40 76-45 SCRAPPER BAR
3 (5x)	3	872 27 05-05	CARRIAGE BOLT 5/16−18 X .625
3 (5x)	4	532 15 53-77	NUT 5/16−18
	4	532 15 53-77	NUT 5/16−18

4 (5x)

01.07.023-B

1	KEY	PART
1	NO.	NO.	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 42 17-26	AUGER ASSEMBLY 30 LH
	2	532 42 17-27	AUGER ASSEMBLY 30 RH

01.07.016-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 22

Contents 1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head MountingRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationSnow Thrower CleaningEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-C 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen HeadlightThrust Washer DriveAxle Shaft Clik PIN921 01.02.002-F Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN01.01.001-B Frame Chassis / Engine / PulleysEngine Model Bottom PANSteer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RHSpring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Decals532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

KEY

AUGER ASSEMBLY 30 LH

AUGER ASSEMBLY 30 RH