Husqvarna 1330SB-XLSB owner manual Handles

Page 27

REPAIR PARTS

HANDLES

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

10

2

11

8 4 7

9 9

5

7 6

1

3

13

8

13

12

14

14

12

01.08.012-A

KEY

PART

DESCRIPTION

NO.

NO.

1532 41 55-39 CONTROL PANEL

2532 42 17-06 CONTROL LEVER LH

3532 42 17-07 CONTROL LEVER RH

4532 41 55-46 TRACTION ROD ARM

5532 42 14-92 IMPELLER ROD ARM

6532 41 26-77 INTERLOCK ROD

7

532 41 26-80

SPACER

8

532 16 96-75

RETAINER

9

817 06 04-08 SCREW 1/4−20 X .50

10

532 41 42-80

KNOB BLACK

11

532 41 42-81

KNOB RED

12

532 17 88-99

HANDLE KNOB

13

819 13 13-16

WASHER 3/8

14

872 12 06-18 CARRIAGE BOLT 3/8−16 X 2.25

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27

Image 27
Contents 1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and NutsUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USECleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BAR532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel GrayClik PIN DriveAxle Shaft Thrust Washer921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley01.01.001-B Bottom PAN Chassis / Engine / PulleysEngine Model FrameSteer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LHAxle Lobe CoverWheel Lobe SpringRetainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of PartsDecals 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Warranty Statement