Husqvarna 1330SB-XLSB 532 42 13-51 Console Panel Gray, 532 42 14-48 Headlight Bezel Gray, Bulb

Page 30

REPAIR PARTS

HANDLES

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41

			KEY	PART	DESCRIPTION
			NO.	NO.	DESCRIPTION
		3	1	532 41 62-88 INTERLOCK SPRING
	2		2	532 41 45-72 INTERLOCK CAM
5	2		3	532 17 88-31 TORSION SPRING
			4	532 16 96-75	RETAINER
			5	817 06 04-10 SCREW 1/4−20 X .625
	1		6	532 42 18-14 INTERLOCK STOP
	1
	6	01.08.007-B

7 5

1	6
1
	4
	5	KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	532 42 13-51 CONSOLE PANEL GRAY
		2	532 42 14-48 HEADLIGHT BEZEL GRAY
		3	532 17 86-66 HALOGEN HEADLIGHT
	4	4	532 18 44-71	SHOULDER SCREW 10−24 X .625
	4	5	532 17 52-62 SCREW 10−24 X 1.25
		5	532 17 52-62 SCREW 10−24 X 1.25
		6	532 41 77-60	GRIP SWITCH
		7	532 40 56-99 WIRE HARNESS
		8	532 40 16-20	BULB

01.10.010-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 30

Image 30

Contents 1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head MountingRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 30 LH Auger Assembly 30 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-C 532 42 14-48 Headlight Bezel Gray Grip Switch532 42 13-51 Console Panel Gray 532 17 86-66 Halogen HeadlightThrust Washer DriveAxle Shaft Clik PIN921 01.02.002-F Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PIN01.01.001-B Frame Chassis / Engine / PulleysEngine Model Bottom PANSteer Cable Bracket LH Wheel Assembly LHWheels Steer Cable Bracket RHSpring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

HANDLES

KEY

KEY

532 42 13-51 CONSOLE PANEL GRAY

532 42 14-48 HEADLIGHT BEZEL GRAY

532 17 86-66 HALOGEN HEADLIGHT

GRIP SWITCH

BULB