Husqvarna 1330SB-XLSB owner manual Decals, 532 18 10-35 DECAL, DANGER, Deflector

Page 39

REPAIR PARTS

DECALS

SNOWTHROWER-MODELNO.1330SB-XLSB(96193004100),PRODUCTNO.9619300-41









 





 



KEY

PART

 

NO.

NO.

DESCRIPTION

1532 18 10-37 DECAL, DANGER

2532 42 37-17 DECAL, HUSQVARNA 1330SB-XLSB

3532 18 10-35 DECAL, DANGER, DEFLECTOR

4532 18 10-42 DECAL, DANGER

5532 42 37-16 DECAL, HUSQVARNA 1330SB-XLSB

6532 18 10-33 DECAL, INSTRUCTION

7532 18 37-30 DECAL, REMOTE DEFLECTOR

9

532 41 54-75 DECAL, SPEED CONTROL

11532 41 53-99 DECAL, LH TRIGGER

12532 41 53-98 DECAL, RH TRIGGER

- -

532 42 35-18

OWNER'S MANUAL, ENGLISH

- -

532 42 35-19

OWNER'S MANUAL, FRENCH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 1330SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and NutsUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USECleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BAR532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel GrayClik PIN DriveAxle Shaft Thrust Washer921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley01.01.001-B Bottom PAN Chassis / Engine / PulleysEngine Model FrameSteer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LHAxle Lobe CoverWheel Lobe SpringRetainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of PartsDecals 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Warranty Statement
Top Page Image Contents